Home › Power Source / Network › 3ZR-FAE BATTERY / CHARGING › CHARGING SYSTEM › from 2015.04
RM3090E _57 Power Source / Network _008394 3ZR-FAE BATTERY / CHARGING _0046852 CHARGING SYSTEM C

3ZR-FAE BATTERY / CHARGING  CHARGING SYSTEM  P161A  Lost Communication with Alternator  


DESCRIPTION

The ECM and generator assembly each detect reception malfunctions. A generator assembly reception malfunction detected by the generator assembly is sent to the ECM via LIN communication. If there is a malfunction in either the ECM or generator assembly, the ECM determines that there is a LIN communication malfunction and outputs a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P161A Lost Communication with Alternator Diagnosis condition: Ignition switch to ON
When the ECM cannot receive LIN communication, the generator assembly cannot receive LIN communication for approximately 17 minutes or more.
Other: 1 trip
·

Generator assembly

·

ECM

·

Wire harness or connector


Displayed DTC stored

WIRING DIAGRAM

A331106E20
6.125,1.865 6.563,2.198 0.438,0.333 10 false ECM 5.813,1.865 6.271,2.063 0.458,0.198 10 false B93 5.865,0.729 6.323,0.927 0.458,0.198 10 false LIN 5.573,0.542 6.031,0.74 0.458,0.198 10 false 61 3.708,0.74 4.167,0.938 0.458,0.198 10 false LIN 4.094,0.531 4.552,0.729 0.458,0.198 10 false 2 2.688,0.729 3.146,0.927 0.458,0.198 10 false +B 2.448,0.583 2.906,0.781 0.458,0.198 10 false 1 1.542,0.896 2.448,1.208 0.906,0.313 10 false ALT-S/ICS 0.573,0.698 1.479,1.01 0.906,0.313 10 false from Battery 2.74,1.219 4.073,1.667 1.333,0.448 10 false Battery State Sensor Assembly 2.396,1.219 2.74,1.552 0.344,0.333 10 false A75 2.844,2.698 4.292,2.969 1.448,0.271 10 false Generator Assembly 2.49,2.708 2.948,2.906 0.458,0.198 10 false B90 3.688,2.208 4.146,2.406 0.458,0.198 10 false LIN 4.094,2.01 4.552,2.208 0.458,0.198 10 false 2 1.083,3.167 3.115,3.396 2.031,0.229 10 false : LIN Communication Line

PROCEDURE

1.CHECK CHARGING SYSTEM

Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the B93 ECM connector.


b.

Disconnect the B90 generator assembly connector.


c.

Disconnect the A75 battery state sensor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-61 (LIN) - B90-2 (LIN) Always Below 1 Ω
B93-61 (LIN) or B90-2 (LIN) - Body ground Ignition switch off
(while LIN communication is stopped)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.READ OUTPUT DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ OUTPUT DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait at least 30 seconds.


f.

Start the engine and wait 17 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
Only P161A is output A
P161A and P162B are output B
No DTC is output C



A

B

C