Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

A235144C01
0.323,0.047 0.514,0.2 0.191,0.153 10 *1 0.756,0.259 0.632,0.117 false 0.632,0.117 0.498,0.117 false 0.547,2.536 0.738,2.689 0.191,0.153 10 *2 0.63,1.87 0.376,2.609 false 0.376,2.609 0.53,2.609 false 2.946,0.231 3.137,0.384 0.191,0.153 10 *a 5.023,0.231 5.214,0.384 0.191,0.153 10 *b
*1 Vacuum Switching Valve (for Acoustic Control Induction System) *2 Intake Air Control Valve
*a Intake Air Control Valve Open *b Intake Air Control Valve Close


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
1.

Voltage of terminal ACIS of the ECM is low when the vacuum switching valve (for acoustic control induction system) is off.

2.

The engine has been started.


·

Open or short in vacuum switching valve (for acoustic control induction system) circuit

·

Vacuum switching valve (for acoustic control induction system)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure)

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0660.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A347027E02
0.625,3.146 1.698,3.344 1.073,0.198 10 false Battery 0.51,2.031 1.583,2.229 1.073,0.198 10 false FL MAIN 0.552,1.146 1.625,1.344 1.073,0.198 10 false EFI-MAIN NO.1 1.677,1.771 2.75,1.969 1.073,0.198 10 false EFI-MAIN NO.1 2.896,1.135 3.635,1.396 0.74,0.26 10 false EFI NO.2 3.729,1.292 4.469,1.552 0.74,0.26 10 false B44 3.729,1.448 5.281,2.042 1.552,0.594 10 false Vacuum Switching Valve (for Acoustic Control Induction System) 5.323,0.99 5.729,1.292 0.406,0.302 10 false B93 5.323,2.458 5.729,2.76 0.406,0.302 10 false A62 5.323,3.083 5.729,3.385 0.406,0.302 10 false B93 5.719,0.865 6.125,1.167 0.406,0.302 10 false ACIS 5.698,2.344 6.229,2.646 0.531,0.302 10 false MREL 5.698,3.083 6.229,3.385 0.531,0.302 10 false E1 5.365,2.896 5.896,3.198 0.531,0.302 10 false 59 5.365,2.26 5.896,2.563 0.531,0.302 10 false 46 5.365,0.792 5.896,1.094 0.531,0.302 10 false 62 4.958,0.854 5.469,1.177 0.51,0.323 10 false 1 3.802,0.833 4.313,1.156 0.51,0.323 10 false 2 1.74,1.333 2.25,1.656 0.51,0.323 10 false 2 2.49,1.333 3,1.656 0.51,0.323 10 false 1 1.74,0.813 2.25,1.135 0.51,0.323 10 false 5 2.49,0.823 3,1.146 0.51,0.323 10 false 3 6.052,3.76 6.583,4.063 0.531,0.302 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR INTAKE CONTROL)
a.
A233358C03
2.646,1.625 2.417,1.625 2.417,1.625 2.219,1.208 false 2.458,3.76 2.229,3.76 2.229,3.76 2.031,3.344 false 1.177,0.979 1.427,1.177 false 0.854,1.24 1.26,1.427 false 0.896,3.177 1.24,3.292 false 0.729,3.427 1.073,3.563 false 0.24,0.26 0.469,0.479 0.229,0.219 10 *a 0.302,2.646 0.521,2.823 0.219,0.177 10 *b 1.031,0.875 1.208,1.083 0.177,0.208 10 *2 0.75,3.083 1.01,3.292 0.26,0.208 10 *2 0.708,1.156 0.969,1.344 0.26,0.188 10 *1 0.563,3.333 0.719,3.531 0.156,0.198 10 *1 1.021,0.469 1.229,0.677 0.208,0.208 10 *c 0.542,1.594 0.75,1.771 0.208,0.177 10 *c 1.146,2.615 1.354,2.823 0.208,0.208 10 *c 2.594,2.979 2.802,3.188 0.208,0.208 10 *c 2.688,1.542 2.948,1.729 0.26,0.188 10 *3 2.51,3.667 2.771,3.854 0.26,0.188 10 *3
*1 Port F
*2 Port E
*3 Air Filter
*a Vacuum Switching Valve (for Acoustic Control Induction System) is ON
*b Vacuum Switching Valve (for Acoustic Control Induction System) is OFF
*c Air


Disconnect the vacuum hose from port F of the vacuum switching valve (for acoustic control induction system).


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

f.

Operate the vacuum switching valve (for acoustic control induction system).


g.

Check the vacuum switching valve (for acoustic control induction system) air flow when switching the vacuum switching valve (for acoustic control induction system).

OK:
Activate the VSV for Intake Control Specified Condition
ON Air from port E flows out through port F
OFF Air from port E flows out through air filter


Result:
Proceed to
OK
NG




OK

NG

2.INSPECT VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)
2.INSPECT VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)
a.

Inspect the vacuum switching valve (for acoustic control induction system) (Click here Engine / Hybrid System>3ZR-FAE INTAKE / EXHAUST>VACUUM SWITCHING VALVE(for ACIS)>ON-VEHICLE INSPECTION).

Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
a.
A225830C08
0.302,1.063 0.698,1.354 0.396,0.292 0.094,0.083 0.406,0.281 0.313,0.198 10 *a 0.375,1.135 0.833,1.333 0.458,0.198 10 B44
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Acoustic Control Induction System))


Disconnect the vacuum switching valve (for acoustic control induction system) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B44-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - EFI-MAIN NO.1 RELAY)

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)
a.

Disconnect the vacuum switching valve (for acoustic control induction system) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B44-1 - B93-62 (ACIS) Always Below 1 Ω
B44-1 or B93-62 (ACIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR