Home › Drivetrain › K114F MULTIDRIVE / CVT › SHIFT LEVER › from 2015.04
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0172320 SHIFT LEVER A

K114F MULTIDRIVE / CVT  SHIFT LEVER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for LHD vehicles.


·

Use the same procedure for RHD and LHD vehicles.



PROCEDURE

Hide 1.INSTALL SHIFT LEVER ASSEMBLY

a.
C279460N02
0.854,1.813 1.01,2.01 0.156,0.198 10 1 2.521,0.708 2.677,0.906 0.156,0.198 10 2 0.875,0.688 1.031,0.885 0.156,0.198 10 3 2.521,1.813 2.677,2.01 0.156,0.198 10 4

Install the shift lever assembly with the 4 bolts. Tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the 2 connectors and attach the 4 harness clamps to the shift lever assembly.

C279459C02
0.385,0.042 0.698,0.24 0.313,0.198 10 false *A 3.99,0.042 4.302,0.24 0.313,0.198 10 false *B
*A for LHD *B for RHD



Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper to lock the nut.

C328348C01
1.49,0.563 1.365,0.271 1.365,0.271 0.906,0.271 true 1.521,1.115 1.708,1.396 1.708,1.396 1.917,1.396 false 0.719,0.177 1.031,0.375 0.313,0.198 10 false *1 1.99,1.313 2.302,1.51 0.313,0.198 10 false *2
*1 Stopper *2 Nut
V113147

Turn in this Direction
V113148

Push in this Direction


NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable assembly will not be reusable.


HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



b.

Install the outer part of the transmission control cable assembly to the shift lever assembly. Check that the stopper returns to the pulled out position.

C328349C01
0.615,0.219 0.948,0.219 0.948,0.219 1.198,0.344 true 0.771,1.448 1.042,1.448 1.042,1.448 1.208,0.844 true 1.052,1.604 1.271,1.604 1.271,1.604 1.333,1.271 true 0.417,0.135 0.729,0.333 0.313,0.198 10 false *1 0.573,1.354 0.885,1.552 0.313,0.198 10 false *2 0.875,1.521 1.188,1.719 0.313,0.198 10 false *3
*1 Stopper *2 Nut
*3 Shift Lever Assembly - -
V113147

Install in this Direction - -



c.
C328343C01
1.073,0.292 1.365,0.292 1.365,0.292 1.75,1.021 true 2.292,1.125 2.51,1.417 2.51,1.417 2.76,1.417 true 2.26,2.083 2.26,1.813 2.26,1.813 2.646,1.813 false 1.177,1.854 1.708,1.854 1.708,1.854 1.823,2.219 false 0.885,0.198 1.198,0.396 0.313,0.198 10 false *1 2.844,1.333 3.156,1.531 0.313,0.198 10 false *2 2.719,1.719 3.031,1.917 0.313,0.198 10 false *2 0.99,1.76 1.302,1.958 0.313,0.198 10 false *1
*1 Slider
*2 Lock Piece
V113147

Slide in this Direction
V113148

Pull in this Direction


Slide the slider in the direction shown in the illustration and pull out the lock piece.


d.
C328345C01
2.01,1.438 2.115,1.333 false
V113147

Connect in this Direction


Connect the end of the transmission control cable assembly to the shift lever.

NOTICE:
·

Make sure that the lock piece is pulled up.


·

Push on the end of the transmission control cable assembly all the way to the base of the pin.




e.

Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.


f.
C328344C01
0.188,0.646 0.188,0.156 0.188,0.156 0.969,0.156 true 1.135,0.583 1.396,0.333 1.396,0.333 3.01,0.333 true 0.656,0.875 0.906,1.25 0.906,1.25 1.177,1.25 true 1.021,0.073 1.333,0.271 0.313,0.198 10 true *1 3.073,0.24 3.385,0.438 0.313,0.198 10 false *2 1.25,1.167 1.563,1.365 0.313,0.198 10 false *3
*1 Cable Rod
*2 Adjuster Case
*3 Lock Piece
V113147

Push in this Direction


Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.



Hide 58901A 4.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY