Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.04–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the acceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.

These DTCs are also output when calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1381 Acceleration Sensor Power Supply Voltage Malfunction At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

A/B fuse

·

Acceleration sensor (Airbag sensor assembly)

·

Acceleration sensor (Airbag sensor assembly) power source circuit



WIRING DIAGRAM

Refer to DTCs C1232, C1243, C1245 and C1279.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1232

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).

K111: Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K111F: Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K114F: Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)
NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.
C233304C01
1.521,0.271 1.969,0.552 0.448,0.281 1.125,1.469 0.563,1.469 false 0.24,1.375 0.49,1.552 0.25,0.177 10 IG2 0.146,0.073 0.333,0.229 0.188,0.156 10 *a 1.615,0.333 1.906,0.49 0.292,0.156 10 G92
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor [Airbag Sensor Assembly])


Disconnect the G92 yaw rate and acceleration sensor (airbag sensor assembly) connector.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G92-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C233304C02
1.521,0.271 2.01,0.563 0.49,0.292 1.813,1.542 2.125,1.802 false 1.667,1.542 1.375,1.802 false 1.229,1.833 1.427,2.01 0.198,0.177 10 E1 2.052,1.833 2.25,2.01 0.198,0.177 10 E2 0.146,0.073 0.333,0.229 0.188,0.156 10 *a 1.615,0.333 1.906,0.49 0.292,0.156 10 G92
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor [Airbag Sensor Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G92-25 (E1) - Body ground Always Below 1 Ω
G92-26 (E2) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the G92 yaw rate and acceleration sensor (airbag sensor assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1381 is not output
DTC C1381 is output



DTC C1381 is not output

DTC C1381 is output