Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM L

2WW ENGINE CONTROL  ECD SYSTEM  PRECAUTION  


INITIALIZATION AND REGISTRATION


NOTICE:
·

When the ECM and/or the other component(s) mentioned below are replaced, perform the following utility items, referring to the corresponding Initialization and Registration procedure.

·

If the ECM is replaced, register the ECU communication ID for Engine Immobiliser System (Refer to the Service Bulletin for Registration).

·

When the cable is disconnected from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected.

System Name See Procedure
Stop and Start System (Click here)
Simple Intelligent Parking Assist System
Power Door Lock Control System



HINT:

When the ECM and other component(s) are replaced at the same time, perform the following utility items by following the instructions shown on the GTS display, starting with the ECM.

Replacement Part Utility Item See page
ECM Learning Values Save (Click here)
Learning Values Write (Click here)
Injector Assembly Injector Compensation (Click here)
Fuel Supply Pump Assembly Supply Pump Learning Value Reset (Click here)
Exhaust Manifold Converter Sub-assembly (Catalytic Converter) DPF History Information Reset (Click here)
NOx Storage Catalyst Learning Value Reset (Click here)
Air Fuel Ratio Sensor O2 Sensor Learning Value Reset (Click here)
Mass Air Flow Meter Sub-assembly Air Flow Meter Learning Value Reset (Click here)
EGR Valve Assembly EGR Learning Value Reset (Click here)
Differential Pressure Sensor Differential Pressure Learning Value Reset (Click here)
Swirl Control Valve Swirl Valve Learning Value Reset (Click here)
Turbo Pressure Sensor Assembly Upstream Turbine Pressure Learning Value Reset (Click here)
Pressure Discharge Valve Fuel PCV Compensation Value Reset (Click here)
Engine Assembly Injector Compensation (Click here)


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

After replacing injector assembly, perform the "Injector Compensation" function using the GTS.

·

After replacing the engine assembly, perform the "Injector Compensation" function using the GTS.




INJECTOR COMPENSATION CODE


A312349C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.271,2.438 1.458,2.635 0.188,0.198 10 false *b
*a Example
*b Injector Compensation Code


HINT:

Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

Injector compensation codes are 7-digit, alphanumeric values printed on the head of each injector assembly.


NOTICE:

If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



FOR USING GTS


CAUTION:
·

Read the instruction manuals before using the GTS.

·

Prevent the GTS cable from being caught on the pedals, shift lever and steering wheel when driving with the GTS connected to the vehicle.

·

When driving the vehicle for testing purposes and using the GTS, two persons are required. One for driving the vehicle, and the other for operating the GTS.




IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition switch off LOCK Off
Ignition switch ACC ACC On (ACC)
Ignition switch ON ON On (IG)
Engine start START Start