Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A"/"B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below.


Signal (ECM terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A"/"B" Correlation When brake pedal is being depressed, STP signal and ST1- signal are OFF.
(2 trip detection logic)
·

Short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

WIRING DIAGRAM

A372441E02
1.26,0.896 3.406,1.094 2.146,0.198 10 false from IG2 Relay 1.396,1.885 3.229,2.083 1.833,0.198 10 false from Battery 3.125,3.042 5.219,3.271 2.094,0.229 10 false Stop Light Switch Assembly 3.469,0.802 3.781,1 0.313,0.198 10 false 6 6,3.156 6.458,3.354 0.458,0.198 10 false ECM 5.99,2.99 6.448,3.188 0.458,0.198 10 false A62 2.74,2.042 3.354,2.24 0.615,0.198 10 false STOP 2.823,1.052 3.438,1.25 0.615,0.198 10 false IGN 3.469,1.792 3.781,1.99 0.313,0.198 10 false 7 4.583,1.792 4.896,1.99 0.313,0.198 10 false 3 5.583,0.792 6.198,0.99 0.615,0.198 10 false ST- 5.583,1.781 6.198,1.979 0.615,0.198 10 false STP 4.583,0.802 4.896,1 0.313,0.198 10 false 5 5.333,0.792 5.646,0.99 0.313,0.198 10 false 10 5.323,1.792 5.635,1.99 0.313,0.198 10 false 48 3.656,0.885 3.969,1.083 0.313,0.198 10 false B 3.656,1.875 3.969,2.073 0.313,0.198 10 false B 4.406,0.906 4.719,1.104 0.313,0.198 10 false L 4.406,1.885 4.719,2.083 0.313,0.198 10 false L 3.146,2.885 3.76,3.083 0.615,0.198 10 false A77 4.188,2.333 4.802,2.531 0.615,0.198 10 false GND 4.583,2.229 4.896,2.427 0.313,0.198 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

5.

Check Stop Light Switch when the brake pedal is depressed and released.

Brake Pedal Operation Specified Condition
Depressed ON
Released OFF




NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.
E270270C18
0.208,1.073 0.656,1.375 0.448,0.302 2.042,1.208 1.479,1.823 true 2.375,1.188 2.792,1.854 true 0.302,1.146 0.76,1.344 0.458,0.198 10 false A77 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.406,1.865 1.563,2.063 0.156,0.198 10 false B 2.781,1.896 2.938,2.094 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-6(B) - Body ground Ignition switch ON 11 to 14 V
A77-7(B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A77-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (STP AND ST1- VOLTAGE)
A311427C04
0.167,3.375 0.604,3.646 0.438,0.271 1.021,4.292 1.271,3.646 false 2.573,4.271 2.167,3.313 false 0.906,0.458 1.219,0.615 0.313,0.156 10 false *a 2.51,0.5 2.823,0.656 0.313,0.156 10 false *b 0.344,2.198 0.656,2.354 0.313,0.156 10 false *c 0.26,3.427 0.646,3.646 0.385,0.219 10 false A62 0.885,4.323 1.531,4.552 0.646,0.229 10 false STP 2.458,4.302 2.969,4.531 0.51,0.229 10 false ST1-
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A62-10 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A62-48 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A77-3 (L) - A62-48 (STP) Always Below 1 Ω
A77-5 (L) - A62-10 (ST1-) Always Below 1 Ω
A77-3 (L) or A62-48 (STP) - Body ground and other terminals Always 10 kΩ or higher
A77-5 (L) or A62-10 (ST1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Start the engine and wait for 15 seconds or more [B].


f.

Release and depress the brake pedal [C].


g.

Repeat [A] through [C] for the number of trips detected.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END