Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0606  Control Module Processor  P060A  Internal Control Module Monitoring Processor Performance  P060C  Internal Control Module Main Processor Performance  P062F  Internal Control Module EEPROM Error  P064D  Internal Control Module O2 Sensor Processor Performance Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0606 Control Module Processor ECM internal error.
(1 trip detection logic)
ECM Comes on DTC stored
P060A Internal Control Module Monitoring Processor Performance ECM internal error.
(1 trip detection logic)
ECM Comes on DTC stored
P060C Internal Control Module Main Processor Performance ECM internal error.
(1 trip detection logic)
ECM Comes on DTC stored
P062F Internal Control Module EEPROM Error ECM internal error.
(1 trip detection logic)
ECM Comes on DTC stored
P064D Internal Control Module O2 Sensor Processor Performance Bank 1 Decrease in ECM supply voltage resulting in insufficient voltage to air fuel ratio sensor circuit.
(3 trip detection logic)
ECM Does not come on DTC stored

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registration for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0606, P060A, P060C, P062F, P064D)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0606, P060A, P060C, P062F and/or P064D A
DTC P0606, P060A, P060C, P062F and/or P064D and other DTCs B


HINT:
·

When DTC P062D is output, DTC P060A may also be output on the next trip. Therefore, when DTC P062D and P060A are output simultaneously, perform troubleshooting for DTC P062D first.

·

If any DTCs other than P0606, P060A, P060C, P062F and/or P064D are output, troubleshoot those DTCs first.





A

2.REPLACE ECM

B

2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END