Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the Starter Control (STA) signal is also sent to terminal STA of the ECM. The STA signal is used to increase the fuel injection volume mainly when starting the engine. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High STA signal is being input to ECM regardless of whether vehicle is in motion.
(1 trip detection logic)
·

Starter relay circuit

·

Ignition switch

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

A359898E03
0.094,0.073 5.052,0.313 4.958,0.24 12 false w/o Entry and Start System: 2.573,0.771 2.958,0.948 0.385,0.177 10 false 17 3.823,0.604 4.208,0.781 0.385,0.177 10 false 10 3.844,1.063 4.229,1.24 0.385,0.177 10 false 21 2.802,0.865 3.188,1.042 0.385,0.177 10 false CLL 3.521,0.698 3.906,0.875 0.385,0.177 10 false NE 3.469,1.156 3.854,1.333 0.385,0.177 10 false STA 2.448,1.333 2.833,1.51 0.385,0.177 10 false A66 2.438,1.521 4.219,1.844 1.781,0.323 10 false Engine Stop and Start ECU 5.948,0.698 6.333,0.875 0.385,0.177 10 false NEO 5.76,0.594 6.146,0.771 0.385,0.177 10 false 6 5.958,5.615 6.344,5.792 0.385,0.177 10 false STA 5.708,5.521 6.094,5.698 0.385,0.177 10 false 36 3,3.115 5.104,3.469 2.104,0.354 10 false Clutch Start Switch Assembly 3.01,2.76 3.396,2.938 0.385,0.177 10 false A4*1 4.292,2.385 4.677,2.563 0.385,0.177 10 false 1 3.448,2.385 3.833,2.563 0.385,0.177 10 false 2 0.552,2.979 2.656,3.333 2.104,0.354 10 false Ignition Switch Assembly 0.552,2.833 0.938,3.01 0.385,0.177 10 false G4 1.927,2.385 2.313,2.563 0.385,0.177 10 false 2 0.635,2.385 1.021,2.563 0.385,0.177 10 false 4 1.583,2.385 1.969,2.563 0.385,0.177 10 false ST2 0.833,2.385 1.219,2.563 0.385,0.177 10 false AM2 0.375,3.698 0.854,3.896 0.479,0.198 10 false AM2 0.99,4.833 1.354,5.177 0.365,0.344 10 false ST 3.479,5.896 4.156,6.188 0.677,0.292 10 false ST NO. 1 3.302,5.083 3.688,5.26 0.385,0.177 10 false 3 3.302,5.521 3.688,5.698 0.385,0.177 10 false 1 4.125,5.073 4.51,5.25 0.385,0.177 10 false 5 4.125,5.521 4.51,5.698 0.385,0.177 10 false 2 2.094,6.104 2.594,6.333 0.5,0.229 10 false B117 1.104,6.344 1.427,6.552 0.323,0.208 10 false C8 2.281,5.906 2.667,6.083 0.385,0.177 10 false 1 1.156,6.146 1.542,6.323 0.385,0.177 10 false 1 1.583,7.302 3.688,7.656 2.104,0.354 10 false Starter Assembly 0.563,6.896 2.667,7.25 2.104,0.354 10 false Battery 0.375,5.74 2.479,6.094 2.104,0.354 10 false FL MAIN 6.323,6.198 6.708,6.375 0.385,0.177 10 false A62 6.323,6.354 6.708,6.531 0.385,0.177 10 false ECM 3.01,2.948 3.396,3.125 0.385,0.177 10 false F2*2 4.271,6.844 5.958,7.042 1.688,0.198 10 false *1: for LHD 4.281,7.188 5.969,7.385 1.688,0.198 10 false *2: for RHD

A321044E07
0.573,7.781 1.646,7.979 1.073,0.198 10 false Battery 1.552,7.969 3.052,8.177 1.5,0.208 10 false Starter Assembly 1.125,7.01 1.531,7.198 0.406,0.188 10 false C8 1.156,6.823 1.427,7.042 0.271,0.219 10 false 1 2.115,6.781 2.521,6.99 0.406,0.208 10 false B117 2.313,6.594 3.385,6.792 1.073,0.198 10 false 1 0.417,6.167 1.49,6.365 1.073,0.198 10 false FL MAIN 1.104,5.573 1.458,5.823 0.354,0.25 10 false ST 4.594,6.354 4.885,6.594 0.292,0.24 10 false 2 4.583,5.979 4.833,6.198 0.25,0.219 10 false 5 3.823,6.354 4.125,6.573 0.302,0.219 10 false 1 3.823,5.99 4.104,6.229 0.281,0.24 10 false 3 3.979,6.771 5.052,6.969 1.073,0.198 10 false ST NO. 1 6.271,7.177 6.667,7.396 0.396,0.219 10 false A62 6.271,7.344 6.875,7.542 0.604,0.198 10 false ECM 5.958,6.458 7.156,6.667 1.198,0.208 10 false STA 5.667,6.333 6.74,6.531 1.073,0.198 10 false 36 0.146,4.5 1.344,4.708 1.198,0.208 10 false G82 0.156,4.667 2.271,5.146 2.115,0.479 10 false Certification ECU (Smart Key ECU Assembly) 1,4.229 2.198,4.438 1.198,0.208 10 false STAR 1.083,3.844 2.281,4.052 1.198,0.208 10 false STA 1.156,3.438 2.354,3.646 1.198,0.208 10 false NE 1.479,3.313 2.552,3.51 1.073,0.198 10 false 16 1.479,3.719 2.552,3.917 1.073,0.198 10 false 7 1.479,4.115 2.552,4.313 1.073,0.198 10 false 5 3.396,3.125 3.927,3.344 0.531,0.219 10 false A4*1 3.385,3.469 4.583,3.875 1.198,0.406 10 false Clutch Start Switch Assembly 3.542,2.677 4.615,2.875 1.073,0.198 10 false 1 4.323,2.688 5.396,2.885 1.073,0.198 10 false 2 5.958,0.885 7.156,1.094 1.198,0.208 10 false NEO 5.75,0.781 6.823,0.979 1.073,0.198 10 false 6 0.177,2.135 1.375,2.344 1.198,0.208 10 false A66 0.177,2.292 2.146,2.552 1.969,0.26 10 false Engine Stop and Start ECU 1.073,0.906 2.271,1.115 1.198,0.208 10 false NE 1.01,1.344 2.208,1.552 1.198,0.208 10 false STA 1.031,1.76 2.229,1.969 1.198,0.208 10 false CLL 1.385,0.792 2.583,1 1.198,0.208 10 false 10 1.385,1.219 2.583,1.427 1.198,0.208 10 false 21 1.396,1.656 2.594,1.865 1.198,0.208 10 false 17 0.177,0.146 3.354,0.75 3.177,0.604 12 false w/ Entry and Start System: 3.396,3.292 3.927,3.51 0.531,0.219 10 false F2*2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table.

·

If this DTC is output, inspect the starter.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 371 149

d.

Read the value displayed on the GTS when the ignition switch is turned to ON.

OK:
Ignition Switch Positions Starter Signal
ON OFF
START ON



Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C



A

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

B

2.CHECK HARNESS AND CONNECTOR

C

3.INSPECT IGNITION SWITCH ASSEMBLY
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-7 (STA) or A62-36 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR

NG

7.REPLACE IGNITION SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the ignition switch connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) or A62-36 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END