Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low  P060D  Internal Control Module Accelerator Pedal Position Performance  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High  


DESCRIPTION

The Accelerator Pedal Position (APP) sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and malfunctions of the accelerator pedal sensor assembly.

In the accelerator pedal sensor assembly, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal which indicates the actual accelerator pedal opening angle and is used for engine control, and the VPA2 is a signal which indicates the information about the opening angle and is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.

A261002E04
4.354,1.99 4.219,1.99 false 4.354,2.198 4.219,2.198 false 4.219,0.979 4.344,1.104 false 4.208,1.208 4.333,1.281 false 4.208,1.448 4.344,1.323 false 4.208,1.635 4.344,1.479 false 5.99,1.448 6.208,1.667 6.208,1.667 6.281,1.667 false 6.26,1.104 6.354,0.438 6.354,0.438 6.458,0.438 false 4.344,0.896 4.031,0.208 4.031,0.208 3.948,0.208 false 0.885,0.833 0.948,0.833 0.948,0.833 0.906,1.646 false 1.156,0.729 1.104,0.729 1.104,0.729 1.021,1.313 false 1.146,2.76 1.083,2.76 1.083,2.76 1.031,2.219 false 0.906,2.698 0.958,2.698 0.958,2.698 0.906,1.979 false 0.646,0.146 4.156,0.531 3.51,0.385 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.5,0.365 7.156,0.635 0.656,0.271 10 false VPA2*3 6.333,1.573 6.802,1.781 0.469,0.208 10 false VPA 0.25,3.146 2.521,3.854 2.271,0.708 10 false Accelerator Pedal Sensor Assembly (Accelerator Pedal Position Sensor) 1.188,0.656 1.948,0.979 0.76,0.323 10 false Magnet 0.365,0.76 1.135,1.094 0.771,0.333 10 false No. 1 IC 0.354,2.625 0.885,2.938 0.531,0.313 10 false No. 2 IC 1.219,2.688 1.906,2.885 0.688,0.198 10 false Magnet 2.208,0.844 2.802,1.083 0.594,0.24 10 false VPA 2.219,1.167 2.802,1.323 0.583,0.156 10 false EPA 2.167,1.479 2.688,1.719 0.521,0.24 10 false VCPA 2.177,1.781 2.667,2.021 0.49,0.24 10 false VPA2 2.177,2.094 2.677,2.313 0.5,0.219 10 false EPA2 2.167,2.427 2.781,2.698 0.615,0.271 10 false VCP2 2.875,3.115 3.438,3.292 0.563,0.177 10 false ECM 0.51,4.063 2.969,4.365 2.458,0.302 10 false *1: Accelerator Pedal Fully Released 0.521,4.458 2.969,4.813 2.448,0.354 10 false *2: Accelerator Pedal Fully Depressed 4.594,2.99 5.969,3.26 1.375,0.271 10 false Opening Angle (deg.) 4.75,2.677 5.688,2.938 0.938,0.26 10 false Usable Range 4.365,0.656 4.667,0.823 0.302,0.167 10 false *1 5.844,0.656 6.135,0.813 0.292,0.156 10 false *2 3.896,0.896 4.385,1.125 0.49,0.229 10 false 4.55 3.844,1.135 4.427,1.313 0.583,0.177 10 false 3.988 3.896,1.406 4.354,1.563 0.458,0.156 10 false 3.75 3.833,1.615 4.427,1.792 0.594,0.177 10 false 3.188 3.99,1.917 4.427,2.115 0.438,0.198 10 false 1.6 4,2.125 4.573,2.333 0.573,0.208 10 false 0.8 4.313,2.677 4.438,2.833 0.125,0.156 10 false 0 5.813,2.688 6.479,2.958 0.667,0.271 10 false 13.1 4.406,2.417 4.958,2.667 0.552,0.25 10 false 0.29 3.26,3.479 7.125,3.771 3.865,0.292 10 false *3: Test pulse is activated cyclically every 320 ms for VPA2. 3.292,3.646 6.917,4.229 3.625,0.583 10 false Therefore small voltage drops in the VPA2 can be observed every 320 ms. But this is only for test purposes and has no influence on accelerator pedal position sensing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P060D Internal Control Module Accelerator Pedal Position Performance The difference between the accelerator pedal voltage VPA and VPA2 is the specified value or less, or the specified value or more.
(1 trip detection logic)
·

Open or short in accelerator pedal sensor assembly circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Condition (a) or (b) continues for 0.5 seconds or more (1 trip detection logic):

(a) VPA is less than 0.2 V when accelerator pedal is fully released, or VPA is more than 4.8 V

(b) VPA2 is less than 0.5 V when accelerator pedal is fully released, or VPA2 is more than 4.8 V


·

Open or short in accelerator pedal sensor assembly circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Condition (a) or (b) continues for 0.5 seconds or more (1 trip detection logic):

(a) VPA is less than 0.2 V when accelerator pedal is fully released, or VPA is more than 4.8 V

(b) VPA2 is less than 0.5 V when accelerator pedal is fully released, or VPA2 is more than 4.8 V


·

Open or short in accelerator pedal sensor assembly circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Condition (a) or (b) continues for 0.5 seconds or more (1 trip detection logic):

(a) VPA is less than 0.2 V when accelerator pedal is fully released, or VPA is more than 4.8 V

(b) VPA2 is less than 0.5 V when accelerator pedal is fully released, or VPA2 is more than 4.8 V


·

Open or short in accelerator pedal sensor assembly circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Condition (a) or (b) continues for 0.5 seconds or more (1 trip detection logic):

(a) VPA is less than 0.2 V when accelerator pedal is fully released, or VPA is more than 4.8 V

(b) VPA2 is less than 0.5 V when accelerator pedal is fully released, or VPA2 is more than 4.8 V


·

Open or short in accelerator pedal sensor assembly circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2122
P2123
P2127
P2128
P060D
·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %



WIRING DIAGRAM

A351151E04
1.458,0.542 2.073,0.74 0.615,0.198 10 false VCPA 1.563,0.958 2.177,1.156 0.615,0.198 10 false VPA 1.573,1.385 2.188,1.583 0.615,0.198 10 false EPA 1.49,1.802 2.104,2 0.615,0.198 10 false VCP2 1.49,2.208 2.104,2.406 0.615,0.198 10 false VPA2 1.49,2.625 2.104,2.823 0.615,0.198 10 false EPA2 0.302,3.063 0.917,3.26 0.615,0.198 10 false A6 0.302,3.229 2.917,3.448 2.615,0.219 10 false Accelerator Pedal Sensor Assembly 2,0.417 2.615,0.615 0.615,0.198 10 false 4 2,0.833 2.615,1.031 0.615,0.198 10 false 6 2.01,1.25 2.625,1.448 0.615,0.198 10 false 5 2.01,1.677 2.625,1.875 0.615,0.198 10 false 1 2.01,2.094 2.625,2.292 0.615,0.198 10 false 3 2.021,2.5 2.635,2.698 0.615,0.198 10 false 2 5.333,0.427 5.948,0.625 0.615,0.198 10 false 27 5.333,0.844 5.948,1.042 0.615,0.198 10 false 52 5.333,1.25 5.948,1.448 0.615,0.198 10 false 22 5.333,1.688 5.948,1.885 0.615,0.198 10 false 29 5.344,2.094 5.958,2.292 0.615,0.198 10 false 43 5.333,2.521 5.948,2.719 0.615,0.198 10 false 23 5.615,0.427 6.229,0.625 0.615,0.198 10 false VCPA 5.615,0.854 6.229,1.052 0.615,0.198 10 false VPA 5.615,1.271 6.229,1.469 0.615,0.198 10 false EPA 5.604,1.677 6.219,1.875 0.615,0.198 10 false VCP2 5.615,2.094 6.229,2.292 0.615,0.198 10 false VPA2 5.615,2.521 6.229,2.719 0.615,0.198 10 false EPA2 6.031,3.083 6.646,3.281 0.615,0.198 10 false A62 6.031,3.24 6.646,3.438 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.
C129061C01
0.854,1.646 1.604,1.854 0.75,0.208 10 *a 0.177,0.115 1.51,0.323 1.333,0.208 10 *1 2.26,1.646 2.927,1.854 0.667,0.208 10 *b
*1 Accelerator Pedal
*a Depressed
*b Released


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 371 11,12

d.

Read the values.

Standard:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (VCP2) - A62-29 (VCP2) Always Below 1 Ω
A6-2 (EPA2) - A62-23 (EPA2) Always Below 1 Ω
A6-3 (VPA2) - A62-43 (VPA2) Always Below 1 Ω
A6-4 (VCPA) - A62-27 (VCPA) Always Below 1 Ω
A6-5 (EPA) - A62-22 (EPA) Always Below 1 Ω
A6-6 (VPA) - A62-52 (VPA) Always Below 1 Ω
A6-1 (VCP2) or A62-29 (VCP2) - Body ground Always 10 kΩ or higher
A6-2 (EPA2) or A62-23 (EPA2) - Body ground Always 10 kΩ or higher
A6-3 (VPA2) or A62-43 (VPA2) - Body ground Always 10 kΩ or higher
A6-4 (VCPA) or A62-27 (VCPA) - Body ground Always 10 kΩ or higher
A6-5 (EPA) or A62-22 (EPA) - Body ground Always 10 kΩ or higher
A6-6 (VPA) or A62-52 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A200914C22
0.375,0.896 0.833,1.167 0.458,0.271 1.333,1.135 0.74,1.646 true 1.49,1.146 1.365,1.646 true 1.771,1.115 2,1.625 true 1.917,1.125 2.646,1.667 true 0.51,0.958 0.906,1.198 0.396,0.24 10 false A6 1.135,1.667 1.667,1.979 0.531,0.313 10 false EPA2 1.792,1.667 2.344,1.885 0.552,0.219 10 false VCPA 0.375,1.667 1,1.969 0.625,0.302 10 false VCP2 0.125,0.094 0.688,0.469 0.563,0.375 10 false *a 2.563,1.667 3.146,1.99 0.583,0.323 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-4 (VCPA) - A6-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A6-1 (VCP2) - A6-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

6.REPLACE ECM
4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more.


e.

Turn the ignition switch to ON.


f.

Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, and then fully open it for 3 seconds.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
DTC P2122, P2123, P2127, P2128 and/or P060D A
No DTC output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more.


e.

Turn the ignition switch to ON.


f.

Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, and then fully open it for 3 seconds.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END