Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  U1500  OMI Not Initialized  


DESCRIPTION

The ECM outputs this DTC when OMI (Oil Maintenance Interval) initialization is not performed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U1500 OMI Not Initialized OMI (Oil Maintenance Interval) initialization is not performed.
(1 trip detection logic)
·

CAN malfunction system

·

ECM


Does not come on DTC stored

HINT:

Normally, the ECM automatically initializes the OMI value and performs learning within a couple of seconds after the ignition switch is turned to ON.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (OIL MAINTENANCE INTERVAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Oil Maintenance Interval.

Powertrain > Engine and ECT > Data List
Tester Display
Oil Maintenance Interval
50003 371 180

d.

Start the engine.


e.

Read the value.

Result:
Result Proceed to
Not Initialized A
Short OMI or Long OMI B




A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Check if CAN malfunction DTCs related to the main body ECU are output.

·
·
·
·

Result:
Result Proceed to
No DTC output A
DTC output B




A

3.CHECK WHETHER DTC OUTPUT RECURS (DTC U1500)

B

3.CHECK WHETHER DTC OUTPUT RECURS (DTC U1500)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.

Result:
Result Proceed to
DTC U1500 A
No DTC output B




A

4.REPLACE ECM

B

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END