Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  P0617  Starter Relay Circuit High  


DESCRIPTION

When the stop and start system is activated, the engine stop and start ECU sends starter operation voltage (STA voltage) to the starter relay (ST relay) and controls the starter assembly.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P0617 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0617 Starter Relay Circuit High Both of the following conditions continue for 1 second (1 trip detection logic):
·

Ignition switch ON

·

Overcurrent to ST relay is detected.


·

Wire harness or connector

·

ST relay

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A375327E02
0.094,0.083 4.073,0.281 3.979,0.198 12 false w/ Entry and Start System: 4.104,0.552 4.563,0.75 0.458,0.198 10 false BBC 4.438,0.25 4.594,0.448 0.156,0.198 10 false 2 3.927,0.25 4.083,0.448 0.156,0.198 10 false 1 6.094,0.354 6.708,0.552 0.615,0.198 10 false BIN1 5.729,0.354 6.188,0.552 0.458,0.198 10 false A86 5.802,0.167 5.958,0.365 0.156,0.198 10 false 3 6.094,1.094 6.708,1.292 0.615,0.198 10 false BIN2 5.729,1.115 6.188,1.313 0.458,0.198 10 false A86 5.802,0.906 5.958,1.104 0.156,0.198 10 false 1 4.104,1.26 5.188,1.458 1.083,0.198 10 false BBC NO. 2 4.625,0.979 4.781,1.177 0.156,0.198 10 false 2 4.146,0.99 4.302,1.188 0.156,0.198 10 false 1 6.094,1.635 6.708,1.833 0.615,0.198 10 false CANH 6.104,2.052 6.719,2.25 0.615,0.198 10 false CANL 1.188,1.646 1.802,1.844 0.615,0.198 10 false CANH 1.219,2.083 1.833,2.281 0.615,0.198 10 false CANL 1.281,2.552 1.74,2.75 0.458,0.198 10 false STA 1.677,2.552 2.135,2.75 0.458,0.198 10 false A62 1.729,2.354 2.042,2.552 0.313,0.198 10 false 29 0.927,2.948 1.385,3.146 0.458,0.198 10 false ECM 0.667,3.604 1.125,3.802 0.458,0.198 10 false AM2 1.406,3.323 1.563,3.521 0.156,0.198 10 false 2 1.615,3.438 1.927,3.635 0.313,0.198 10 false +B 2.188,3.438 2.802,3.635 0.615,0.198 10 false STAR 2.292,3.792 2.75,3.99 0.458,0.198 10 false STA 2.688,3.313 2.844,3.51 0.156,0.198 10 false 5 2.688,3.667 2.844,3.865 0.156,0.198 10 false 7 3.76,3.313 3.917,3.51 0.156,0.198 10 false 2 4.656,3.313 4.813,3.51 0.156,0.198 10 false 1 3.656,3.75 5.188,3.948 1.531,0.198 10 false A4*1, F2*2 3.656,3.948 4.99,4.375 1.333,0.427 10 false Clutch Start Switch Assembly (for Lower) 5.719,3.448 6.177,3.646 0.458,0.198 10 false A66 5.771,3.25 6.083,3.448 0.313,0.198 10 false 21 6.104,3.427 6.563,3.625 0.458,0.198 10 false STA 6.104,2.906 6.563,3.104 0.458,0.198 10 false CLL 5.719,2.906 6.177,3.104 0.458,0.198 10 false A66 5.771,2.688 6.083,2.885 0.313,0.198 10 false 17 6.083,4.26 6.698,4.458 0.615,0.198 10 false DGND 5.729,4.26 6.188,4.458 0.458,0.198 10 false A66 5.823,4.063 5.979,4.26 0.156,0.198 10 false 6 1.167,4.083 1.625,4.281 0.458,0.198 10 false G82 1.167,4.281 2.698,4.833 1.531,0.552 10 false Certification ECU (Smart Key ECU Assembly) 5.917,5.24 6.979,5.677 1.063,0.438 10 false Engine Stop and Start ECU 3.49,5.396 3.802,5.594 0.313,0.198 10 false ST 4.333,6.396 4.646,6.594 0.313,0.198 10 false ST 4.854,5.688 5.01,5.885 0.156,0.198 10 false 5 4.854,5.979 5.01,6.177 0.156,0.198 10 false 2 3.969,5.958 4.125,6.156 0.156,0.198 10 false 1 3.979,5.677 4.135,5.875 0.156,0.198 10 false 3 3.365,5.792 3.677,5.99 0.313,0.198 10 false B6 3.427,5.583 3.583,5.781 0.156,0.198 10 false 1 1.406,6.115 1.719,6.313 0.313,0.198 10 false C4 1.458,5.885 1.615,6.083 0.156,0.198 10 false 1 0.469,5.729 1.542,5.927 1.073,0.198 10 false FL MAIN 0.563,6.917 1.635,7.115 1.073,0.198 10 false Battery 0.896,7.479 4.563,7.677 3.667,0.198 10 false : CAN Communication Line 1.865,6.438 4.313,6.635 2.448,0.198 10 false Starter Assembly 5.729,1.646 6.188,1.844 0.458,0.198 10 false G87 5.771,1.448 6.083,1.646 0.313,0.198 10 false 13 5.729,2.083 6.188,2.281 0.458,0.198 10 false G87 5.76,1.896 6.073,2.094 0.313,0.198 10 false 14 1.688,2.094 2.146,2.292 0.458,0.198 10 false A62 1.688,1.646 2.146,1.844 0.458,0.198 10 false A62 1.719,1.438 2.031,1.635 0.313,0.198 10 false 13 1.719,1.885 2.031,2.083 0.313,0.198 10 false 26 5.427,6.656 6.24,6.854 0.813,0.198 10 false *1: for LHD 5.438,7.052 6.25,7.25 0.813,0.198 10 false *2: for RHD

A375328E02
0.083,0.083 5.042,0.323 4.958,0.24 12 false w/o Entry and Start System: 3.99,0.469 4.448,0.667 0.458,0.198 10 false BBC 4.292,0.177 4.448,0.375 0.156,0.198 10 false 2 3.823,0.177 3.979,0.375 0.156,0.198 10 false 1 4.281,1.042 5.406,1.25 1.125,0.208 10 false BBC NO. 2 4.802,0.74 5.094,0.969 0.292,0.229 10 false 2 4.292,0.75 4.448,0.948 0.156,0.198 10 false 1 6.125,0.302 6.74,0.5 0.615,0.198 10 false BIN1 6.125,0.875 6.74,1.073 0.615,0.198 10 false BIN2 5.729,0.302 6.188,0.5 0.458,0.198 10 false A86 5.74,0.885 6.198,1.083 0.458,0.198 10 false A86 5.813,0.115 5.969,0.313 0.156,0.198 10 false 3 5.813,0.698 5.969,0.896 0.156,0.198 10 false 1 1.188,1.396 1.802,1.594 0.615,0.198 10 false CANH 1.188,1.844 1.802,2.042 0.615,0.198 10 false CANL 6.083,1.375 6.698,1.573 0.615,0.198 10 false CANH 6.094,1.844 6.708,2.042 0.615,0.198 10 false CANL 1.688,2.333 2.146,2.531 0.458,0.198 10 false A62 1.74,2.135 2.052,2.333 0.313,0.198 10 false 29 1.292,2.333 1.75,2.531 0.458,0.198 10 false STA 0.99,2.719 1.448,2.917 0.458,0.198 10 false ECM 0.604,3.719 1.063,3.917 0.458,0.198 10 false AM2 1.625,3.458 2.083,3.656 0.458,0.198 10 false AM2 1.417,3.427 1.573,3.625 0.156,0.198 10 false 4 2.688,3.406 2.844,3.604 0.156,0.198 10 false 2 2.354,3.458 2.813,3.656 0.458,0.198 10 false ST2 1.521,3.917 1.833,4.115 0.313,0.198 10 false G4 1.531,4.115 2.646,4.521 1.115,0.406 10 false Ignition or Starter Switch Assembly 3.271,3.823 4.802,4.021 1.531,0.198 10 false A4*1, F2*2 3.26,4.021 5.156,4.427 1.896,0.406 10 false Clutch Start Switch Assembly (for Lower) 3.771,3.396 4.063,3.625 0.292,0.229 10 false 2 4.667,3.396 4.823,3.594 0.156,0.198 10 false 1 5.74,2.854 6.198,3.052 0.458,0.198 10 false A66 5.781,2.656 6.094,2.854 0.313,0.198 10 false 28 6.115,2.865 6.573,3.063 0.458,0.198 10 false CLL 6.094,3.563 6.552,3.76 0.458,0.198 10 false STA 5.729,3.563 6.188,3.76 0.458,0.198 10 false A66 5.771,3.354 6.083,3.552 0.313,0.198 10 false 21 6.104,4.219 6.719,4.417 0.615,0.198 10 false DGND 5.74,4.198 6.198,4.396 0.458,0.198 10 false A66 5.802,4 5.958,4.198 0.156,0.198 10 false 6 4.365,6.135 4.677,6.333 0.313,0.198 10 false ST 3.635,5.156 3.948,5.354 0.313,0.198 10 false ST 4.865,5.438 5.021,5.635 0.156,0.198 10 false 5 3.979,5.448 4.135,5.646 0.156,0.198 10 false 3 3.969,5.719 4.125,5.917 0.156,0.198 10 false 1 4.865,5.719 5.156,5.948 0.292,0.229 10 false 2 3.385,5.542 3.698,5.74 0.313,0.198 10 false B6 3.427,5.323 3.583,5.521 0.156,0.198 10 false 1 1.396,5.865 1.708,6.063 0.313,0.198 10 false C4 1.458,5.656 1.615,5.854 0.156,0.198 10 false 1 0.458,5.438 1.531,5.635 1.073,0.198 10 false FL MAIN 1.885,6.281 4.333,6.479 2.448,0.198 10 false Starter Assembly 0.542,6.635 1.615,6.833 1.073,0.198 10 false Battery 0.875,7.469 4.542,7.667 3.667,0.198 10 false : CAN Communication Line 5.917,5.365 6.969,5.938 1.052,0.573 10 false Engine Stop and Start ECU 5.729,1.385 6.188,1.583 0.458,0.198 10 false G87 5.76,1.188 6.073,1.385 0.313,0.198 10 false 13 5.719,1.833 6.177,2.031 0.458,0.198 10 false G87 5.76,1.635 6.073,1.833 0.313,0.198 10 false 14 1.688,1.844 2.146,2.042 0.458,0.198 10 false A62 1.677,1.385 2.135,1.583 0.458,0.198 10 false A62 1.729,1.635 2.042,1.833 0.313,0.198 10 false 26 1.719,1.188 2.031,1.385 0.313,0.198 10 false 13 5.198,6.594 6.885,6.792 1.688,0.198 10 false *1: for LHD 5.188,6.958 6.875,7.156 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC, BBC NO. 2 FUSE)
a.

Disconnect the A86 engine stop and start ECU connector.


b.

Remove the BBC fuse from the engine room relay block and junction block assembly.


c.

Remove the BBC NO. 2 fuse from the engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - BBC NO. 2 fuse terminal 2 Always Below 1 Ω
A86-3 (BIN1) - BBC fuse terminal 2 Always Below 1 Ω
A86-1 (BIN2) - Body ground Always 10 kΩ or higher
A86-3 (BIN1) - Body ground Always 10 kΩ or higher
BBC fuse terminal 2 - Body ground Always 10 kΩ or higher
BBC NO. 2 fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
a.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A62 ECM connector.


c.

Disconnect the A86 and A66 engine stop and start ECU connectors.


d.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


e.

Remove the BBC fuse and BBC NO. 2 fuse from the engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher
A86-1 (BIN2) - A66-21 (STA) Always 10 kΩ or higher
A86-3 (BIN3) - A66-21 (STA) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
A375785C01
1.51,0.135 1.938,0.427 0.427,0.292 3.156,0.125 3.583,0.417 0.427,0.292 4.948,0.125 5.375,0.417 0.427,0.292 5.51,1.948 5.938,2.24 0.427,0.292 3.188,1.969 3.615,2.26 0.427,0.292 1.094,2 1.521,2.292 0.427,0.292 1.594,0.198 1.969,0.396 0.375,0.198 10 false A86 3.25,0.188 3.625,0.385 0.375,0.198 10 false A66 5.031,0.188 5.406,0.385 0.375,0.198 10 false G87 1.167,2.063 1.542,2.26 0.375,0.198 10 false A86 3.25,2.031 3.625,2.229 0.375,0.198 10 false A66 5.583,2.021 5.958,2.219 0.375,0.198 10 false G87 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the A66 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - A66-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RELAY (ST RELAY)

NG

4.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

NG

REPLACE RELAY (ST RELAY)