Refer to DTC B22C0
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>B22C0
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P323B | Backup Boost Converter | Any of the following conditions is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected ·
Engine stop and start ECU thermistor temperature is 128°C (262.4°F) or higher ·
Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (104°F) or higher ·
B41 voltage is 6.0 V or less, backup boost converter is not overheating and backup boost converter output overcurrent is not detected ·
IG41 voltage is 6.0 V or less and backup boost converter output overcurrent is not detected |
·
Engine stop and start ECU ·
Wire harness or connector ·
Battery ·
BBC fuse ·
BBC NO. 2 fuse |
Blinks | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Keep the engine stopped by stop and start control for 1 second or more.
Depress the clutch pedal and start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.
Check that DTCs are not output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Allow the engine to stop by stop and start control.
Depress the clutch pedal and start the engine.
Refer to DTC B22C0
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>B22C0
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA
Disconnect the A86 engine stop and start ECU connector.
Remove the BBC fuse from the engine room relay block and junction block assembly.
Remove the BBC NO. 2 fuse from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-1 (BIN2) - BBC NO. 2 fuse terminal 2 | Always | Below 1 Ω |
| A86-3 (BIN1) - BBC fuse terminal 2 | Always | Below 1 Ω |
| A86-1 (BIN2) - Body ground | Always | 10 kΩ or higher |
| BBC NO. 2 fuse terminal 2 - Body ground | Always | 10 kΩ or higher |
| A86-3 (BIN1) - Body ground | Always | 10 kΩ or higher |
| BBC fuse terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector:
(to Engine Stop and Start ECU) |
Disconnect the engine stop and start ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-1 (BIN2) - Body ground | Always | 9.5 to 14 V |
| A86-3 (BIN1) - Body ground | Always | 9.5 to 14 V |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G87-21 (IG1) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-6 (DGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G87 engine stop and start ECU connector.
Disconnect the 3D instrument panel junction block assembly (main body ECU (multiplex network body ECU)) connector.
w/ EC Mirror:
Disconnect the Q14*1 or Q15*2 inner rear view mirror assembly connector.
*1: w/o Lane Departure Alert System
*2: w/ Lane Departure Alert System
w/ Tire Pressure Warning System:
Disconnect the M30 tire pressure warning ECU and receiver connector.
Disconnect the G170 network gateway ECU connector.
w/ Dynamic Radar Cruise Control System:
Disconnect the Z6 millimeter wave radar sensor assembly connector.
w/ Dynamic Radar Cruise Control System:
Disconnect the G168 driving support ECU assembly connector.
w/ Lane Departure Alert System:
Disconnect the Q17 lane departure warning camera connector.
w/ Blind Spot Monitor System:
Disconnect the R1 blind spot monitor sensor LH connector.
w/ Blind Spot Monitor System:
Disconnect the T1 blind spot monitor sensor RH connector.
w/ Panoramic View Monitor System:
Disconnect the a2 parking assist ECU connector.
for Radio Receiver Type:
Disconnect the G46 radio receiver assembly connector.
for Navigation Receiver Type:
Disconnect the G137 navigation receiver assembly connector.
for Radio and Display Receiver Type:
Disconnect the G141 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G87-3 (IG41) - 3D-40 (IG) | Always | Below 1 Ω |
| G87-3 (IG41) - Q14-1 (IG)*1, *10 | Always | Below 1 Ω |
| G87-3 (IG41) - Q15-4 (IG)*2, *10 | Always | Below 1 Ω |
| G87-3 (IG41) - M30-1 (IG)*3 | Always | Below 1 Ω |
| G87-3 (IG41) - G170-11 (IG1) | Always | Below 1 Ω |
| G87-3 (IG41) - Z6-8 (IGB)*4 | Always | Below 1 Ω |
| G87-3 (IG41) - G168-7 (IGB)*4 | Always | Below 1 Ω |
| G87-3 (IG41) - Q17-7 (IGB)*2 | Always | Below 1 Ω |
| G87-3 (IG41) - R1-5 (BLB)*5 | Always | Below 1 Ω |
| G87-3 (IG41) - T1-5 (BRB)*5 | Always | Below 1 Ω |
| G87-3 (IG41) - a2-6 (IG)*6 | Always | Below 1 Ω |
| G87-2 (B41) - a2-2 (+B)*6 | Always | Below 1 Ω |
| G87-2 (B41) - G46-4 (+B1)*7 | Always | Below 1 Ω |
| G87-2 (B41) - G137-4 (+B1)*8 | Always | Below 1 Ω |
| G87-2 (B41) - G141-4 (+B1)*9 | Always | Below 1 Ω |
| G87-3 (IG41) - Body ground | Always | 10 kΩ or higher |
| G87-2 (B41) - Body ground | Always | 10 kΩ or higher |
*1: w/o Lane Departure Alert System
*2: w/ Lane Departure Alert System
*3: w/ Tire Pressure Warning System
*4: w/ Dynamic Radar Cruise Control System
*5: w/ Blind Spot Monitor System:
*6: w/ Panoramic View Monitor System
*7: for Radio Receiver Type
*8: for Navigation Receiver Type
*9: for Radio and Display Receiver Type
*10: w/ EC Mirror
| Proceed to |
|---|
| OK |
| NG |
OK
NG