Home › Engine / Hybrid System › 2WW COOLING › COOLING FAN SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044377 2WW COOLING _0211204 COOLING FAN SYSTEM J

2WW COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM turns the fan relays on or off using signals based on the engine coolant temperature, air conditioning switch condition (on/off) (w/ Air Conditioning System) and refrigerant pressure (w/ Air Conditioning System), as well as the engine speed and vehicle speed signals.

The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan High Speed
50004 371 10

e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan Low Speed

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan Low Speed
50004 371 11

f.

Perform the Active Test according to the display on the GTS.

OK:
Tester Operation Fan Operation
ON (Actuator Test of Fan High Speed) Cooling fans operate in high speed
ON (Actuator Test of Fan Low Speed) Cooling fans operate in low speed
OFF Cooling fans stop



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (FANL - FANH POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (FANL - FANH POWER SOURCE)
a.

Disconnect the A62 ECM connector.


b.

Turn the ignition switch to ON.


c.
A355840C10
0.292,1.052 0.698,1.292 0.406,0.24 2.073,1.24 2.063,1.958 true 2.583,1.365 2.583,0.167 2.583,0.167 2.75,0.167 true 1.896,1.99 2.313,2.167 0.417,0.177 10 false FANL 0.375,1.083 0.896,1.323 0.521,0.24 10 false A62 0.135,0.125 0.656,0.365 0.521,0.24 10 false *a 2.792,0.104 3.208,0.281 0.417,0.177 10 false FANH
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-45 (FANH) - Body ground Ignition switch ON 11 to 14 V
A62-20 (FANL) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

NG

12.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)
3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)
a.
A377232C01
0.052,0.063 0.365,0.26 0.313,0.198 10 false *1 2.521,1.073 2.833,1.271 0.313,0.198 10 false *3 2.51,2.229 2.823,2.427 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 1 Relay
*3 FAN NO. 3 Relay


Remove the FAN NO. 1 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V
3 (FAN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

4.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)
a.

Inspect the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.

Click hereEngine / Hybrid System>2WW COOLING>RELAY>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (FAN NO. 1 relay) B
NG (FAN NO. 2 relay) C
NG (FAN NO. 3 relay) D



A

5.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

B

REPLACE FAN NO. 1 RELAY

C

REPLACE FAN NO. 2 RELAY

D

REPLACE FAN NO. 3 RELAY

5.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
a.
A377233C01
0.042,0.052 0.354,0.25 0.313,0.198 10 false *1 2.563,0.604 2.875,0.802 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 2 Relay


Remove the FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
5 (FAN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

6.INSPECT COOLING FAN MOTOR

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the A52 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A52-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

8.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A52 cooling fan motor connector.


b.
A377235C01
0.052,0.052 0.365,0.25 0.313,0.198 10 false *1 2.51,1.958 2.823,2.156 0.313,0.198 10 false *2 2.563,0.615 2.875,0.813 0.313,0.198 10 false *3
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay


Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A52-2 - 5 (FAN NO. 1 relay) Always Below 1 Ω
A52-2 - 4 (FAN NO. 2 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A52-2 or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher
A52-2 or 4 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 2 COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

9.INSPECT NO. 2 COOLING FAN MOTOR
a.

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPLACE NO. 2 COOLING FAN MOTOR

10.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A51 No. 2 cooling fan motor connector.


b.
A377234C01
0.063,0.063 0.375,0.26 0.313,0.198 10 false *1 2.479,1.958 2.792,2.156 0.313,0.198 10 false *3 2.573,0.594 2.885,0.792 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 2 Relay
*3 FAN NO. 3 Relay


Remove the FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A51-1 - 3 (FAN NO. 2 relay) Always Below 1 Ω
A51-2 - 5 (FAN NO. 3 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A51-1 or 3 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher
A51-2 or 5 (FAN NO. 3 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)
a.
A377235C01
0.052,0.052 0.365,0.25 0.313,0.198 10 false *1 2.51,1.958 2.823,2.156 0.313,0.198 10 false *2 2.563,0.615 2.875,0.813 0.313,0.198 10 false *3
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay


Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) - 1 (FAN NO. 2 relay) Always Below 1 Ω
2 (FAN NO. 1 relay) - 2 (FAN NO. 2 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) or 1 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher
2 (FAN NO. 1 relay) or 2 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY

12.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)
a.

Inspect the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.

Click hereEngine / Hybrid System>2WW COOLING>RELAY>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (FAN NO. 1 relay) B
NG (FAN NO. 2 relay) C
NG (FAN NO. 3 relay) D



A

13.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - ECM)

B

REPLACE FAN NO. 1 RELAY

C

REPLACE FAN NO. 2 RELAY

D

REPLACE FAN NO. 3 RELAY

13.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - ECM)
a.
A377236C01
0.052,0.052 0.365,0.25 0.313,0.198 10 false *1 2.49,0.146 2.802,0.344 0.313,0.198 10 false *3 2.5,2.406 2.813,2.604 0.313,0.198 10 false *2 2.49,1.25 2.802,1.448 0.313,0.198 10 false *4
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay
*4 FAN NO. 3 Relay


Remove the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2 (FAN NO. 1 relay) - A62-45 (FANH) Always Below 1 Ω
2 (FAN NO. 2 relay) - A62-45 (FANH) Always Below 1 Ω
2 (FAN NO. 3 relay) - A62-20 (FANL) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
2 (FAN NO. 1 relay) or A62-45 (FANH) - Body ground Always 10 kΩ or higher
2 (FAN NO. 2 relay) or A62-45 (FANH) - Body ground Always 10 kΩ or higher
2 (FAN NO. 3 relay) or A62-20 (FANL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY- ECM)