Home › Engine / Hybrid System › 2WW ENGINE MECHANICAL › ENGINE › from 2015.10
RM3090E _51 Engine / Hybrid System _044373 2WW ENGINE MECHANICAL _0211282 ENGINE G

2WW ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Turn all the electrical systems and A/C off.

·

Inspect the engine idle speed with the cooling fan off.

·

When checking the idle speed, move the shift lever to neutral.



HINT:
·

For more information about the GTS, refer to its operator's manual.

·

If the GTS is not available, use a tachometer as a substitute.



a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and idle it.


iii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9


c.

When not using the GTS:

i.
A206183C92
0.75,1.906 0.896,1.906 0.896,1.906 1.021,1.49 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 0.448,1.823 0.906,2.021 0.458,0.198 10 false TAC
*a Front view of DLC3


Connect a probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

SST
09843-18040  


ii.

Start the engine and idle it.



d.

Inspect the engine idle speed.

Standard Idle Speed:

830 rpm



e.

Turn the ignition switch off.


f.

Disconnect the GTS or tachometer probe from the DLC3.


Hide 2.INSPECT MAXIMUM ENGINE SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum engine speed.

Maximum engine speed (reference):

3800 rpm



Hide 3.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Remove the glow plug assemblies.

Click hereEngine / Hybrid System>2WW STARTING>GLOW PLUG>REMOVAL


c.

Disconnect the injector assembly connectors.


d.

Inspect the cylinder compression pressure.

i.
A318509C01
1.365,0.458 1.49,0.458 1.49,0.458 1.75,1.115 true 1.146,0.354 1.344,0.552 0.198,0.198 10 true *a
*a SST (Compression Gauge Attachment)


Insert SST (compression gauge attachment) into the glow plug assembly hole.

SST
09992-52010  


ii.
A318550C01
2.573,0.448 2.76,0.448 2.76,0.448 2.927,0.896 true 2.344,0.365 2.542,0.583 0.198,0.219 10 true *a
*a SST (Compression Gauge)


Connect SST (compression gauge) to SST (compression gauge attachment).

SST
09992-19015  (09992-10010, 09992-10020)


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure (reference):

1600 kPa (16.3 kgf/cm2, 232 psi) or higher


Difference between each cylinder:

All cylinders almost same value


NOTICE:
·

Use a fully-charged battery to obtain an engine speed of 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression as quickly as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the glow plug assembly holes, and then inspect it again. If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged. If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the cylinder head gasket.



e.

Remove SST (compression gauge attachment and compression gauge).


f.

Connect the injector assembly connectors.


g.

Install the glow plug assemblies.

Click hereEngine / Hybrid System>2WW STARTING>GLOW PLUG>INSTALLATION