Home › Drivetrain › EA64 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT › from 2015.10
RM3090E _52 Drivetrain _008755 EA64 MANUAL TRANSMISSION / TRANSAXLE _0048555 MANUAL TRANSAXLE UNIT A

EA64 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 33242L 1.INSTALL SHIFT FORK SHAFT BEARING

a.
C278118N01
2.042,1.219 2.479,0.75 2.479,0.75 2.708,0.75 false 2.781,0.667 3.24,0.865 0.458,0.198 10 SST

Using SST and a press, press in 4 new shift fork shaft bearings.

SST
09820-00031  

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)



Hide 33134B 2.INSTALL OUTPUT SHAFT COVER

a.
C115413C03
1.115,0.979 0.594,0.979 0.594,0.979 0.594,1.188 false 1.219,1.01 0.885,0.469 0.885,0.469 0.698,0.469 false 0.5,1.25 0.74,1.479 0.24,0.229 10 false *b 0.448,0.365 0.667,0.583 0.219,0.219 10 false *a
*a Protrusion
*b Groove


Install the output shaft cover as shown in the illustration.


Hide 33322B 3.INSTALL FRONT NO. 2 OUTPUT SHAFT BEARING OUTER RACE

a.
C116970N02
0.061,1.151 0.373,1.457 0.312,0.306 10 SST 1.185,1.435 0.443,1.237 0.443,1.237 1.287,1.117 false

Using SST and a hammer, tap in the front No. 2 output shaft bearing outer race.

SST
09950-60020  (09951-00720)
09950-70010  (09951-07100)


Hide 33134B 4.INSTALL OUTPUT SHAFT COVER

a.
C113608C03
1.104,0.906 0.938,1.229 0.938,1.229 0.604,1.229 false 1.26,1.01 0.948,0.292 0.948,0.292 0.729,0.292 false 0.49,0.198 0.719,0.365 0.229,0.167 10 false *a 0.365,1.146 0.583,1.333 0.219,0.188 10 false *b
*a Protrusion
*b Groove


Install the output shaft cover as shown in the illustration.


Hide 33321N 5.INSTALL FRONT OUTPUT SHAFT BEARING

a.
C116969N02
0.539,0.184 0.848,0.424 0.309,0.24 10 SST 0.9,0.262 1.08,0.262 1.08,0.262 1.283,0.605 false

Using SST and a press, install a new front output shaft bearing to the front transaxle case.

SST
09223-15020  


b.
C278099

Install the bearing lock plate with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


c.

Coat a front output shaft bearing with gear oil.


Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.
C217582N01
0.255,0.617 0.661,0.801 0.406,0.184 10 SST 1.125,1.472 0.626,0.711 false 0.626,0.712 1.16,1.259 false

Using SST and a hammer, install a new transaxle case oil seal to the front transaxle case.

SST
09950-60010  (09951-00420)

Standard depth:

4.4 to 5.0 mm (0.174 to 0.196 in.)



b.

Coat the lip of the transaxle case oil seal with MP grease.


Hide 33311A 7.INSTALL FRONT INPUT SHAFT BEARING

a.
C116968N02
0.254,0.37 0.559,0.586 0.305,0.216 10 SST 0.61,0.47 0.821,0.47 0.821,0.47 1.491,0.913 false

Using SST and a press, install a new front input shaft bearing to the front transaxle case.

SST
09223-00010  


b.
C278098

Install the bearing lock plate with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


c.

Coat the front input shaft bearing with gear oil.


Hide 33311P 8.INSTALL REAR INPUT AND OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C116544

Using a snap ring expander, install the rear input and output shaft bearing shaft snap rings.


Hide 33261K 9.INSTALL SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C277772N01
0.875,0.813 1.167,0.813 1.167,0.813 1.333,1.198 false 0.51,0.729 0.875,0.896 0.365,0.167 10 SST

Using SST and a press, press in a new shift and select lever shaft needle roller bearing.

SST
09285-76010  

Clearance:

177.8 to 178.7 mm (7.00 to 7.03 in.)



Hide 33242L 10.INSTALL SHIFT FORK SHAFT BEARING

a.
C277757N01
1.438,1.635 0.333,2.469 0.333,2.469 1.427,1.427 false 0.156,2.521 0.5,2.708 0.344,0.188 10 SST 2.417,4.26 2.604,4.427 0.188,0.167 10 A 2.26,3.333 2.469,3.51 0.208,0.177 10 B

Using SST and a press, press in 4 new shift fork shaft bearings to the manual transmission case.

SST
09307-12010  
09820-00031  

Clearance A:

168.2 to 169.3 mm (6.63 to 6.66 in.)


Clearance B:

162.2 to 163.3 mm (6.39 to 6.42 in.)



Hide 41311E 11.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C116967N02
0.57,0.665 0.864,0.844 0.295,0.179 10 SST 1.565,1.455 0.953,0.768 0.953,0.768 1.69,0.738 false

Using SST and a hammer, tap in the front differential case front tapered roller bearing.

SST
09950-70010  (09951-07150)
09951-00900  


Hide 41311F 12.INSTALL FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING

a.
C116564

Install the front differential case rear shim into the manual transmission case.


b.
C116966N02
0.335,0.933 0.669,1.11 0.334,0.177 10 SST 1.259,1.44 0.727,1.033 0.727,1.033 1.393,1.151 false

Using SST and a hammer, install the front differential case rear outer race bearing.

SST
09950-70010  (09951-07100)
09951-00900  


Hide 33111J 13.INSTALL MANUAL TRANSMISSION CASE STRAIGHT PIN

C278093C01
2.229,2.844 2.635,2.844 false 2.719,2.76 3.031,2.958 0.313,0.198 10 *a
*a Protrusion


a.

Using a plastic-faced hammer, tap in the 4 new manual transmission case straight pins to the front transaxle case.

Protrusion height:

10.5 to 11.5 mm (0.414 to 0.452 in.)



Hide 14.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C115412

Coat the front differential case assembly with gear oil and install it to the front transaxle case.


b.
C327697

Install the manual transmission case to the front transaxle case with the 12 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C327698

Install the 6 bolts to the front transaxle case side.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


d.

Turn the differential case in both directions and make sure it turns smoothly.


e.
C118859C01
2.667,1.552 2.667,1.604 false 1.729,1.542 1.729,1.333 1.729,1.333 0.906,1.323 false 2.073,1.781 2.073,1.615 2.073,1.615 2.667,1.583 false 1.625,1.583 1.938,1.76 0.313,0.177 10 SST 2,1.833 2.26,2.042 0.26,0.208 10 *a
*a Mark


Using SST and a torque wrench, measure the starting preload.

SST
09564-33010  

Standard Preload (at starting):

1.0 to 2.49 N*m (11 to 25 kgf*cm, 9 to 22 in.*lbf)


If the preload is not as specified, replace the front differential case rear shim with one of a different thickness. Use the table below to select a front differential case rear shim which will ensure that the preload is within the specification.


Standard Shim Thickness:
Mark Specified Condition Mark Specified Condition
0 2.00 mm (0.0787 in.) 9 2.45 mm (0.0965 in.)
1 2.05 mm (0.0807 in.) A 2.50 mm (0.0984 in.)
2 2.10 mm (0.0827 in.) B 2.55 mm (0.1004 in.)
3 2.15 mm (0.0846 in.) C 2.60 mm (0.1024 in.)
4 2.20 mm (0.0866 in.) D 2.65 mm (0.1043 in.)
5 2.25 mm (0.0886 in.) E 2.70 mm (0.1063 in.)
6 2.30 mm (0.0906 in.) F 2.75 mm (0.1083 in.)
7 2.35 mm (0.0925 in.) G 2.80 mm (0.1102 in.)
8 2.40 mm (0.0945 in.) H 2.85 mm (0.1122 in.)



f.

Remove the 18 bolts and manual transmission case.


Hide 33322A 15.INSTALL REAR NO. 2 OUTPUT SHAFT BEARING OUTER RACE

a.
C116565C01
1.698,1.344 1.698,1.469 false 0.448,1.115 0.958,1.115 0.958,1.115 1.698,1.385 false 0.188,1.031 0.406,1.229 0.219,0.198 10 *a
*a Mark


Install the rear output shaft bearing shim to the manual transmission case.

HINT:

When reusing the output shaft rear tapered roller bearing, first install a shim of the same thickness as the original. When installing a new output shaft front bearing, first select and install a rear output shaft bearing shim which is thinner than the original.



b.
C116971N02
0.224,0.409 0.535,0.571 0.31,0.162 10 SST 1.364,1.371 0.587,0.498 0.587,0.498 1.444,0.803 false

Using SST and a hammer, install the rear No. 2 output shaft bearing outer race.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07200)


Hide 16.ADJUST REAR NO. 2 OUTPUT SHAFT BEARING PRELOAD

a.
C118441

Install the No. 2 output shaft assembly and front differential case assembly to the front transaxle case.


b.
C327697

Install the manual transmission case to the front transaxle case with the 12 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C327698

Install the 6 bolts to the front transaxle case side.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


d.
C115445N02
2.052,1.698 1.875,1.698 1.875,1.698 0.938,1.427 false 2.115,1.625 2.406,1.896 0.292,0.271 10 false SST

Using SST and a torque wrench, measure the rear No. 2 output shaft bearing preload. Subtract the value of the differential side bearing preload from the measured rear No. 2 output shaft bearing preload.

SST
09564-33010  

Standard Preload (at starting):

4.14 to 5.87 N*m (43 to 59 kgf*cm, 37 to 51 in.*lbf)


If the preload is not as specified, replace the shim with one of a different thickness. Use the table below to select a shim which will ensure that the preload is within the specification.

Bearing Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 1.80 mm (0.0709 in.) K 2.25 mm (0.0886 in.)
B 1.85 mm (0.0728 in.) L 2.30 mm (0.0906 in.)
C 1.90 mm (0.0748 in.) M 2.35 mm (0.0925 in.)
D 1.95 mm (0.0768 in.) N 2.40 mm (0.0945 in.)
E 2.00 mm (0.0787 in.) P 2.45 mm (0.0965 in.)
F 2.05 mm (0.0807 in.) Q 2.50 mm (0.0984 in.)
G 2.10 mm (0.0827 in.) R 2.55 mm (0.1004 in.)
H 2.15 mm (0.0846 in.) S 2.60 mm (0.1024 in.)
J 2.20 mm (0.0866 in.) T 2.65 mm (0.1043 in.)



e.

Remove the 18 bolts and manual transmission case.


f.

Remove the No. 2 output shaft assembly from the front transaxle case.


g.

Remove the front differential assembly case from the front transaxle case.


Hide 33449 17.INSTALL TRANSMISSION MAGNET

a.
C115449

Clean and install the transmission magnet to the front transaxle case.


Hide 41301L 18.INSTALL FRONT DIFFERENTIAL CASE ASSEMBLY

a.
C115412

Coat the front differential case assembly with gear oil, and install it to the front transaxle case.


Hide 33176B 19.INSTALL TRANSMISSION OIL SEPARATOR

a.
C277758

for Front Transaxle Case Side:

Install the transmission oil separator to the front transaxle case with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 33311 20.INSTALL INPUT SHAFT, NO. 1 OUTPUT SHAFT ASSEMBLY AND NO. 2 OUTPUT SHAFT ASSEMBLY

a.
C116196

Install the 3 shafts at the same time.


Hide 33461 21.INSTALL REVERSE IDLER GEAR

a.
C277716

Coat the reverse idler gear, needle roller bearing and reverse idler thrust washer with MP grease, and install them to the reverse idler gear shaft.

HINT:

Make sure that the protruding part of the reverse idler thrust washer fits into the groove of the reverse idler shaft.



b.
C277759

Install the reverse idler gear shaft by sliding and lifting it.


c.
C116861C02
1.5,0.938 0.49,1.781 0.49,1.781 1.042,1.083 false 0.396,1.854 0.635,2.042 0.24,0.188 10 *a 0.052,0.385 0.313,0.542 0.26,0.156 10 30°
*a Align the Mark


Align the mark of the reverse idler gear shaft with the hole of the bolt.


Hide 33211 22.INSTALL REVERSE SHIFT FORK

a.
C115432

Install the reverse shift fork to the No. 2 output shaft assembly.


Hide 33214G 23.INSTALL NO. 3 GEAR SHIFT FORK

a.
C277715

Install the No. 3 gear shift fork to the No. 2 output shaft assembly.


Hide 33244J 24.INSTALL 5TH AND 6TH SHIFT FORK SHAFT

a.
C115431

Install the 5th and 6th shift fork shaft to the front transaxle case.


b.

Coat the threads of the bolt with adhesive.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C115430

Install the bolt to the No. 3 gear shift fork.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 33245H 25.INSTALL REVERSE SHIFT FORK SHAFT

a.
C115429

Install the reverse shift fork shaft to the front transaxle case.


b.

Coat the threads of the bolt with adhesive.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C115428

Install the bolt to the reverse gear shift fork.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 33222F 26.INSTALL SHIFT ARM

a.
C116744

Install the shift arm to the front transaxle case.


Hide 33212A 27.INSTALL NO. 1 GEAR SHIFT FORK

a.
C115443

Install the No. 1 gear shift fork to the No. 1 output shaft assembly.


Hide 33246C 28.INSTALL NO. 5 GEAR SHIFT FORK SHAFT

a.
C118185

Install the No. 3 gear shift head to the No. 5 gear shift fork shaft.


b.

Using a 5 mm pin punch and hammer, tap a new pin into the No. 3 gear shift head.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)



c.
C115442

Install the No. 5 gear shift fork shaft to the front transaxle case.


d.
C116567

Connect the shift arm to the No. 5 gear shift fork shaft.


e.
C115441

Install the pin to the shift arm.


f.
C116568

Using a brass bar and hammer, tap a new E-ring to the pin.


Hide 33213G 29.INSTALL NO. 2 GEAR SHIFT FORK

a.
C115439

Install the No. 2 gear shift fork to the No. 1 output shaft assembly.


Hide 33243F 30.INSTALL 3RD AND 4TH SHIFT FORK SHAFT

a.
C115438

Install the No. 2 gear shift head to the 3rd and 4th shift fork shaft.


b.

Install the 3rd and 4th shift fork shaft to the front transaxle case.


c.
C115437

Using a 5 mm pin punch and hammer, tap a new pin into the No. 2 gear shift fork.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)



d.
C115436

Using a 5 mm pin punch and hammer, tap a new pin into the No. 2 gear shift head.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)



Hide 33242F 31.INSTALL 1ST AND 2ND SHIFT FORK SHAFT

a.
C116327

Install the 1st and 2nd shift fork shaft to the front transaxle case.


b.

Coat the threads of the bolt with adhesive.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C115434

Install the bolt to the No. 1 gear shift fork.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 33176B 32.INSTALL TRANSMISSION OIL SEPARATOR

a.
C277755

for Manual Transmission Case Side:

Install the transmission oil separator to the manual transmission case with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 33124C 33.INSTALL NO. 1 OIL RECEIVER PIPE

a.
C113590

Install the No. 1 oil receiver pipe to the manual transmission case.

NOTICE:

Do not damage the No. 1 oil receiver pipe.



Hide 33111 34.INSTALL MANUAL TRANSMISSION CASE

a.

Clean the contact surface of the manual transmission case and front transaxle case with non-residue solvent.


b.
C113589C02
1.198,0.323 1.031,0.198 1.031,0.198 0.719,0.198 false 0.469,0.115 0.688,0.292 0.219,0.177 10 *a
*a Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal diameter:

1.2 mm (0.0472 in.)


NOTICE:

Assemble parts within 10 minutes of application. Otherwise, the seal packing must be removed and reapplied.



c.
C116542

Using 2 pairs of snap ring pliers to keep the snap ring stretched, install the manual transmission case.


d.
C277717C01
3.167,3.052 3.396,3.26 0.229,0.208 10 *a 0.313,3.854 0.542,4.031 0.229,0.177 10 *b
*a 8.5 mm (0.3346 in.)
*b 9.3 mm (0.3661 in.)


Install a bolt to the No. 1 output shaft assembly and lift the No. 1 output shaft assembly from the service hole. Make sure that the output shaft rear bearing shaft snap ring and input shaft bearing shaft snap ring are positioned correctly in the bearing grooves by checking that the distances between the centers of snap ring holes are as shown in the illustration.


e.
C327697

Install the manual transmission case to the front transaxle case with the 12 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


f.
C327698

Install the 6 bolts to the front transaxle case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 35.INSTALL REVERSE IDLER GEAR SHAFT BOLT

a.
C116545

Coat the reverse idler gear shaft bolt with adhesive, and install a new gasket and the shaft bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 33275C 36.INSTALL SHIFT DETENT BALL

a.

Clean the threads of the 4 detent ball plugs.


b.
C113593

Apply a few drops of adhesive to 2 or 3 threads of each of the 4 detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Using a 6 mm hexagon wrench, install the 4 shift detent balls, 4 shift detent ball compression springs, 4 No. 1 shift ball spring seats and 4 detent ball plugs.

Torque:
22.4 N*m (228 kgf*cm, 17 ft.*lbf)


Hide 33111A 37.INSTALL MANUAL TRANSMISSION CASE PLUG

a.

Clean the contact surface of the manual transmission case and manual transmission case plug.


b.
C277760C02
0.573,2.24 0.573,1.885 0.573,1.885 1.271,1.26 false 0.5,2.313 0.729,2.51 0.229,0.198 10 false *a 1.427,3.802 1.719,4 0.292,0.198 10 true A 1.938,3.635 2.26,3.833 0.323,0.198 10 true B
*a Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



c.

Apply a few drop of the adhesive to 2 or 3 threads of the 2 manual transmission case plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Install the 2 manual transmission case plugs to the manual transmission case.

Torque:
for manual transmission case plug A : 55 N*m (561 kgf*cm, 41 ft.*lbf)
for manual transmission case plug B : 22.4 N*m (228 kgf*cm, 17 ft.*lbf)


Hide 33403L 38.INSTALL O-RING

a.
C277749

Coat a new O-ring with MP grease, and install it to the shift and select lever shaft straight pin (B).


Hide 33261F 39.INSTALL SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN

a.
C277761N01
0.979,0.896 1.24,1.094 0.26,0.198 10 (A) 1.396,1.385 1.667,1.583 0.271,0.198 10 (B)

Install the spring.


b.

While pressing in the shift and select lever shaft straight pin (A) in as far as it will go, push in the shift and select lever shaft straight pin (B) to install it.


Hide 33101A 40.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C113635

Install a new gasket and the manual transmission filler plug.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33104 41.INSTALL DRAIN PLUG

a.
C113634

Install a new gasket and the drain plug.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 31105H 42.INSTALL TRANSMISSION CASE OIL SEAL

Hide 31105H 43.INSTALL TRANSAXLE CASE OIL SEAL

Hide 33251A 44.INSTALL SHIFT AND SELECT LEVER ASSEMBLY

a.
C277762

Align the 4 shift fork shafts as shown in the illustration.


b.

Clean the contact surface of the manual transmission case and shift and select lever assembly.


c.

Clean the threads of the bolts with non-residue solvent.


d.
C113550C03
0.854,1.813 0.854,1.542 0.854,1.542 1.281,1.292 false 0.781,1.865 1.021,2.042 0.24,0.177 10 *a
*a Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



e.

Apply a few drops of adhesive to 2 or 3 threads of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
C341646

Install the shift and select lever assembly to the manual transmission case with the 4 bolts.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 33295B 45.INSTALL SHIFT GATE PIN

a.
C116598

Apply a few drops of the adhesive to 2 or 3 threads of the shift gate pin.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.

Install the shift gate pin to the manual transmission case.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 33290B 46.INSTALL NO. 2 LOCK BALL ASSEMBLY

a.

Clean the threads of the No. 2 lock ball assembly with non-residue solvent.


b.
C116599

Apply a few drops of the adhesive to 2 or 3 threads of the No. 2 lock ball assembly.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Install the No. 2 lock ball assembly to the manual transmission case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33290 47.INSTALL NO. 1 LOCK BALL ASSEMBLY

a.

Clean the threads of the No. 1 lock ball assembly with non-residue solvent.


b.
C116559

Apply a few drops of the adhesive to 2 or 3 threads of the No. 1 lock ball assembly.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Install the No. 1 lock ball assembly to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 84545 48.INSTALL NEUTRAL POSITION SWITCH

a.
C341645N01
0.583,0.833 0.75,0.833 0.75,0.833 1.313,1.219 true 0.25,0.75 0.708,0.948 0.458,0.198 10 false SST

Using SST, install a new gasket and the neutral position switch to the manual transmission case.

SST
09817-16011  

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 84210 49.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C341644N01
0.5,1.25 0.667,1.25 0.667,1.25 1.365,0.938 true 0.208,1.167 0.667,1.365 0.458,0.198 10 false SST

Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.

SST
09817-16011  

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 33590F 50.INSTALL FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY

a.
C344266

Install the floor shift selecting bell crank assembly to the manual transmission case with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 33524B 51.INSTALL CONTROL CABLE BRACKET

a.
C344265

Install the control cable bracket to the manual transaxle assembly with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 31236B 52.INSTALL RELEASE FORK SUPPORT

Hide 31126 53.INSTALL CLUTCH RELEASE FORK BOOT

a.
C341643

Install the clutch release fork boot to the front transaxle assembly.


Hide 31204 54.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 55.INSTALL CLUTCH RELEASE BEARING ASSEMBLY