Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0172311 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with continuously variable transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 36100A 1.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

Transfer Side:

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>REASSEMBLY


a.

Clean the bolt holes.


b.

Apply adhesive 1324 to 2 or 3 threads on one half of a new transfer and transaxle setting stud bolt A as shown in the illustration.

C295653C03
0.583,1.24 0.896,1.438 0.313,0.198 10 false *a 0.604,1.479 0.917,1.677 0.313,0.198 10 false *b 4.406,0.198 4.563,0.396 0.156,0.198 10 false A 5.813,0.438 5.969,0.635 0.156,0.198 10 false B 2.021,0.313 2.146,0.479 0.125,0.167 10 true A 2.573,1.573 2.729,1.75 0.156,0.177 10 false B
*a Adhesive 1324 *b Sealant


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Do not apply adhesive 1324 to the ends of the stud bolt.

·

Install the stud bolt immediately after applying adhesive or sealant to prevent the adherence of foreign matter.




c.

Install the 2 new transfer and transaxle setting stud bolts to the transaxle case positions shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the stud bolt so that the side that has sealant or adhesive is facing the continuously variable transaxle assembly.


HINT:
Stud bolt length
·

Stud bolt A: 73 mm (2.87 in.)

·

Stud bolt B: 47 mm (1.85 in.)




Hide 35151K 2.INSTALL AUTOMATIC TRANSMISSION CASE COVER

a.

Install the automatic transmission case cover to the continuously variable transaxle assembly with the 2 clips.


Hide 35141D 3.INSTALL BREATHER PLUG HOSE

NOTICE:

When replacing the continuously variable transaxle assembly, be sure to install the breather plug hose.


HINT:

Perform this procedure only when replacement of the breather plug hose is necessary.


a.
C330783C01
2.01,1.406 2.573,1.406 false 1.698,1.854 2.292,1.854 false 1.469,0.667 2.156,0.667 false 2.646,1.323 2.958,1.521 0.313,0.198 10 false *1 1.531,1.771 1.844,1.969 0.313,0.198 10 false *2 2.24,0.563 2.552,0.76 0.313,0.198 10 false *3
*1 Breather Plug
*2 O-ring
*3 Breather Plug Hose


Install a new O-ring to a new breather plug.


b.

Install a new breather plug to the breather plug hose.


c.

Install the breather plug hose sub-assembly to the continuously variable transaxle assembly.


Hide 35125A 4.INSTALL TRANSMISSION OIL FILLER TUBE STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the transmission oil filler tube straight screw plug is necessary.


a.

Install a new gasket and the transmission oil filler tube straight screw plug to the continuously variable transaxle assembly.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 32901F 5.INSTALL OIL COOLER ELBOW SUB-ASSEMBLY

a.

Install a new gasket and oil cooler elbow sub-assembly to the continuously variable transaxle assembly with the union bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)

NOTICE:
·

Make sure to insert the painted end (white) of the No. 2 transmission oil cooler hose up to the spool fitting of the oil cooler elbow sub-assembly so that the marking is facing the front of the vehicle.

·

Make sure to clean and degrease the insertion part of the No. 2 transmission oil cooler hose of the oil cooler elbow sub-assembly.




b.

Install the No. 2 transmission oil cooler hose to the oil cooler elbow sub-assembly and slide the clip to secure it.


Hide 32921P 6.INSTALL OIL COOLER TUBE UNION

a.

Install a new O-ring to the oil cooler tube union.


b.

Install the oil cooler tube union to the continuously variable transaxle assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Make sure to insert the painted end (white) of the No. 1 transmission oil cooler hose up to the spool fitting of the oil cooler tube union so that the marking is facing the front of the vehicle.

·

Make sure to clean and degrease the insertion part of the No. 1 transmission oil cooler hose of the oil cooler tube union.




c.

Install the No. 1 transmission oil cooler hose to the oil cooler tube union and slide the clip to secure it.


Hide 7.INSTALL WIRE HARNESS CLAMP BRACKET

C295567C04
1.406,3.135 1.406,2.823 true 5.979,4.313 6.458,4.313 true 6.281,2 6.563,2 false 1.188,1.167 1.583,1.167 true 0.552,0.656 0.906,0.656 true 1.354,3.167 1.667,3.365 0.313,0.198 10 true *1 6.51,4.24 6.823,4.438 0.313,0.198 10 true *1 6.615,1.938 6.927,2.135 0.313,0.198 10 false *1 1.646,1.104 1.958,1.302 0.313,0.198 10 true *3 0.385,0.594 0.646,0.792 0.26,0.198 10 false *2
*1 Wire Harness Clamp Bracket *2 Water By-pass Hose Clamp
*3 Water Hose Clamp Bracket - -


a.

Install the 3 wire harness clamp brackets to the continuously variable transaxle assembly with the 3 bolts.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


b.

Install the water by-pass hose clamp to the water hose clamp bracket.


c.

Install the water hose clamp bracket to the continuously variable transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 33829 8.INSTALL TRANSMISSION CONTROL CABLE SUPPORT

a.

Install the transmission control cable support to the continuously variable transaxle assembly with the 2 bolts.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 33823 9.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the clamp to the No. 1 transmission control cable bracket.


Hide 30400B 10.INSTALL CVT TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands, and then apply MP grease to the entire periphery of the lip of a new CVT type T oil seal.


b.

Temporarily install the CVT type T oil seal by pressing it to the installation surface of the oil pump housing manually.

NOTICE:

Be sure to install the CVT type T oil seal in the correct direction.



c.

Clean the CVT type T oil seal contact surface of SST and the area around it.

SST
09309-36010  


d.
C208789C01
1.802,1.792 1.802,2.469 false 1.698,2.5 2.125,2.74 0.427,0.24 10 SST 0.917,2.458 1.135,2.656 0.219,0.198 10 *a
*a 0 to 0.5 mm (0 to 0.0196 in.)


Using SST, drive the CVT type T oil seal in evenly, until it is even with the side surface of the oil pump housing.

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:
·

Drive the CVT type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT type T oil seal has been driven in until it is even with the side surface of the oil pump housing.

·

Wipe any extra grease off with your hand.



HINT:

The CVT type T oil seal should be driven in between 0 to 0.5 mm (0 to 0.0196 in.) as measured from the side surface of the oil pump housing.



Hide 32000A 11.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C299234C01
1.917,0.292 1.917,0.094 1.917,0.094 2.646,0.094 false 2.708,0.031 3.021,0.229 0.313,0.198 10 false *a
*a Matchmark


Turn the front oil pump drive gear so that the wide groove is at the top and place a matchmark on the transaxle housing.

NOTICE:

Align the matchmark with the wide groove of the transaxle housing.



b.
C295655C01
1.76,0.323 2.417,0.323 false 1.344,1.99 1.688,1.99 1.688,1.99 1.688,1.594 false 2.479,0.25 2.792,0.448 0.313,0.198 10 false *a 1.146,1.917 1.458,2.115 0.313,0.198 10 false *b
*a Key
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.


c.
C295656C01
0.427,0.135 0.802,0.135 0.802,0.135 1.25,0.385 false 0.792,0.135 1.25,0.646 false 1.375,1.969 1.896,1.969 1.896,1.969 2.688,0.865 true 1.885,1.969 2.688,1.188 true 0.24,0.052 0.552,0.25 0.313,0.198 10 false *a 1.188,1.896 1.5,2.094 0.313,0.198 10 false *1
*1 CVT Type T Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT type T oil seal.




d.
C295657C01
1.25,0.375 1.417,0.198 1.417,0.198 1.646,0.198 false 0.75,2 1.042,2 1.042,2 1.25,1.542 true 1.594,1.969 1.875,1.969 1.875,1.969 2.625,0.865 true 1.875,1.969 2.656,1.229 true 0.563,1.917 0.875,2.115 0.313,0.198 10 false *a 1.708,0.125 2.021,0.323 0.313,0.198 10 false *a 1.417,1.896 1.729,2.094 0.313,0.198 10 false *1
*1 CVT Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT type T oil seal.




e.
C295658C01
0.458,0.125 0.76,0.125 0.76,0.125 1.24,0.375 true 0.76,0.125 1.25,0.646 true 1.469,1.99 1.74,1.99 1.74,1.99 2.625,0.875 true 1.729,1.99 2.656,1.229 true 0.292,0.042 0.604,0.24 0.313,0.198 10 false *a 1.292,1.917 1.604,2.115 0.313,0.198 10 false *1
*1 CVT Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C295659C01
0.656,3.104 0.656,2.26 true 0.51,1.51 0.323,0.469 0.323,0.469 0.719,0.469 true 2.385,1.302 2.594,1.302 2.594,1.302 2.594,1 false 2.385,1.885 2.594,1.885 2.594,1.885 2.729,1.573 false 0.594,3.146 0.906,3.344 0.313,0.198 10 false *b 0.781,0.406 1.094,0.604 0.313,0.198 10 false *a 2.208,1.219 2.521,1.417 0.313,0.198 10 false *a 2.219,1.813 2.531,2.01 0.313,0.198 10 false *b 2.729,0.375 2.885,0.573 0.156,0.198 10 false A
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the continuously variable transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C295660E01
2.583,0.385 2.74,0.583 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30400 12.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C300330C02
1.552,0.938 2.146,0.667 2.146,0.667 2.615,0.667 true 2.677,0.615 2.99,0.813 0.313,0.198 10 false *a 0.99,1.083 1.302,1.281 0.313,0.198 10 false *1
*1 Crankshaft
*a Torque Converter Assembly Centerpiece


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz)



b.
C298056E01
1.104,2.271 1.26,2.469 0.156,0.198 10 false A 2.417,2.146 2.729,2.344 0.313,0.198 10 false A 2.656,2.427 2.969,2.625 0.313,0.198 10 false A 0.719,2.927 0.875,3.125 0.156,0.198 10 false B 0.917,4.115 1.073,4.313 0.156,0.198 10 false B 1.292,4.385 1.448,4.583 0.156,0.198 10 false B 2.333,4.323 2.49,4.521 0.156,0.198 10 false B 2.802,4.135 2.958,4.333 0.156,0.198 10 false B

Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.

Install the continuously variable transaxle assembly to the engine assembly with the 8 bolts.

Torque:
Bolt (A) : 38 N*m (387 kgf*cm, 28 ft.*lbf)
Bolt (B) : 40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the 2 knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A): Install from continuously variable transaxle assembly side

·

Bolt (B): Install from engine assembly side




Hide 36100 13.INSTALL TRANSFER ASSEMBLY

Hide 43457 14.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 12325A 16.INSTALL ENGINE MOUNTING BRACKET LH

a.

Clean and degrease the bolt holes of the continuously variable transaxle assembly.


b.
C303453N01
1.708,0.854 1.823,1.01 0.115,0.156 10 true A 1.083,1.833 1.198,1.99 0.115,0.156 10 true B 2.073,1.521 2.219,1.667 0.146,0.146 10 true C 2.51,0.594 2.656,0.74 0.146,0.146 10 true D 1.469,0.156 1.615,0.302 0.146,0.146 10 true E 1.198,0.76 1.313,0.927 0.115,0.167 10 true F

Install the engine mounting bracket LH and engine mounting stay LH with the 6 new bolts.

Torque:
Bolt (A), (B), (C), (D) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (E), (F) : 69 N*m (704 kgf*cm, 51 ft.*lbf)

NOTICE:

Tightening order: Tighten bolt (A), (B), (C), (D) → Tighten bolt (E) → Tighten bolt (F)



Hide 12311A 17.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C328294N01
1.448,0.25 1.604,0.448 0.156,0.198 10 true A 1.802,1.427 1.958,1.625 0.156,0.198 10 false B 1.948,0.281 2.104,0.479 0.156,0.198 10 true C

Install the front engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Tightening order: Temporarily install bolt (A) →Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 12321A 18.INSTALL REAR ENGINE MOUNTING BRACKET

a.
C295574E01
1.729,0.292 1.885,0.49 0.156,0.198 10 true A 1.719,1.688 1.875,1.885 0.156,0.198 10 true B 0.729,1.104 0.885,1.302 0.156,0.198 10 true C 0.74,1.521 0.896,1.719 0.156,0.198 10 true D

Install the rear engine mounting bracket to the continuously variable transaxle assembly with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (D) → Tighten bolt (A)



Hide 35141D 20.CONNECT BREATHER PLUG HOSE

a.

Connect the breather plug hose to the clamp.

NOTICE:

When installing a new continuously variable transaxle assembly, make sure to remove the double clamp attached to the breather hose.



Hide 82121 21.CONNECT ENGINE WIRE

a.
C295566

Connect the 2 connectors.


b.

Attach the 2 clamps.


c.

Connect the engine wire with the 2 bolts and nut.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


d.
C295565

Attach the 4 clamps to install the engine wire.


e.

Connect the engine wire with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


f.

Connect the 5 connectors.


Hide 16267J 22.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 3 water by-pass hose with each one on the oil cooler.

·

Fully insert the No. 3 water by-pass hose to the 2nd rib on each oil cooler pipe.




Hide 16282 23.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Connect the No. 5 water by-pass hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 5 water by-pass hose with each one on the oil cooler.

·

Fully insert the No. 5 water by-pass hose to the 2nd rib on each oil cooler pipe.




Hide 32101G 25.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Using SST, hold the crankshaft pulley.

SST
09213-54015  
09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-00850 (quantity: 2)



b.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


c.
A057108C45
1.708,1.906 1.948,1.5 false 1.552,1.833 1.75,2.021 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 6 drive plate and torque converter assembly setting bolts, apply adhesive to the 6 drive plate and torque converter assembly setting bolts and install them within 10 minutes of adhesive application.



d.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.



Hide 11361J 26.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.