Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P1780  Discrepancy between Neutral Position SW and Shift Position  


DESCRIPTION

The engine stop and start ECU detects malfunctions by comparing the conditions of the shift position signal and NSW signal. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator light, prohibits stop and start control and stores DTC P1780.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1780 Discrepancy between Neutral Position SW and Shift Position Both of the following conditions are met for 2 seconds or more (2 trip detection logic) (*1):
·

Ignition switch ON

·

NSW signal is ON with the shift lever in D


Both of the following conditions are met for 2 seconds or more (2 trip detection logic) (*1):
·

Ignition switch ON

·

NSW signal is ON with the shift lever in R


Both of the following conditions are met for 15 seconds or more (2 trip detection logic) (*2):
·

Ignition switch ON

·

NSW signal is ON with the shift lever in P or N


·

Park/neutral position switch assembly

·

Engine stop and start ECU

·

ECM

·

Wire harness or connector


Blinks DTC stored

*1: "ON" is displayed for the freeze frame data item [Neutral Switch Stuck ON]

*2: "ON" is displayed for the freeze frame data item [Neutral Switch Stuck OFF]

WIRING DIAGRAM

A348495E09
4.417,1.667 5.781,2.25 1.365,0.583 10 false Park/Neutral Position Switch Assembly 4.417,1.469 4.875,1.667 0.458,0.198 10 false B36 3.885,1.177 4.042,1.375 0.156,0.198 10 false 4 3.875,1.438 4.031,1.635 0.156,0.198 10 false B 3.885,2.271 4.042,2.469 0.156,0.198 10 false L 3.885,2.531 4.042,2.729 0.156,0.198 10 false 9 3.333,2.271 3.646,2.469 0.313,0.198 10 false DL 3.417,2.531 3.573,2.729 0.156,0.198 10 false 7 2.885,2.271 3.198,2.469 0.313,0.198 10 false NL 2.969,2.531 3.125,2.729 0.156,0.198 10 false 8 3.708,4.115 4.969,4.344 1.26,0.229 10 false to ST NO. 1 Relay 5.354,4.24 7.125,4.479 1.771,0.24 10 false Engine Stop and Start ECU 3.26,0.552 4.656,0.771 1.396,0.219 10 false to GAUGE Fuse 0.552,0.969 1.01,1.167 0.458,0.198 10 false NSW 1.021,0.969 1.479,1.167 0.458,0.198 10 false A62 1.073,0.771 1.385,0.969 0.313,0.198 10 false 23 2.427,2.281 2.74,2.479 0.313,0.198 10 false RL 2.51,2.521 2.667,2.719 0.156,0.198 10 false 2 1.927,2.271 2.24,2.469 0.313,0.198 10 false PL 2.021,2.51 2.177,2.708 0.156,0.198 10 false 3 2.667,1.448 2.979,1.646 0.313,0.198 10 false RB 2.771,1.177 2.927,1.375 0.156,0.198 10 false 1 0.698,2.667 0.917,2.865 0.219,0.198 10 false P 1.031,2.677 1.49,2.875 0.458,0.198 10 false B93 1.073,2.469 1.385,2.667 0.313,0.198 10 false 70 0.677,3.094 0.896,3.292 0.219,0.198 10 false R 0.677,3.51 0.896,3.708 0.219,0.198 10 false N 0.677,3.99 0.896,4.188 0.219,0.198 10 false D 1.021,3.979 1.479,4.177 0.458,0.198 10 false B93 1.021,3.531 1.479,3.729 0.458,0.198 10 false B93 1.021,3.094 1.479,3.292 0.458,0.198 10 false B93 1.083,2.885 1.396,3.083 0.313,0.198 10 false 64 1.083,3.333 1.396,3.531 0.313,0.198 10 false 69 1.083,3.771 1.396,3.969 0.313,0.198 10 false 65 5.813,3.542 6.271,3.74 0.458,0.198 10 false A66 5.875,3.333 6.188,3.531 0.313,0.198 10 false 21 6.229,3.531 6.688,3.729 0.458,0.198 10 false STA 5.823,0.979 6.281,1.177 0.458,0.198 10 false A66 6.219,0.958 6.677,1.156 0.458,0.198 10 false CLL 5.875,0.76 6.188,0.958 0.313,0.198 10 false 17 0.406,4.948 0.865,5.146 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
-
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in R
ON: Shift lever in R
-
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in N
ON: Shift lever in N
-
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in D or M
ON: Shift lever in D or M
-
Powertrain > Engine and ECT > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 125,126,127,128

Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL)

NG

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List.


b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
-
Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
50003 234 147

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - B36-9 (L) Always Below 1 Ω
A66-17 (CLL) - B36-4 (B) Always Below 1 Ω
A66-21 (STA) - Body ground Always 80 to 180 Ω
A66-17 (CLL) - Body ground Always 10 kΩ or higher
B36-9 (L) - Body ground Always 80 to 180 Ω
B36-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A62 and B93 ECM connectors.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-70 (P) - B36-3 (PL) Always Below 1 Ω
B93-64 (R) - B36-2 (RL) Always Below 1 Ω
B93-69 (N) - B36-8 (NL) Always Below 1 Ω
B93-65 (D) - B36-7 (DL) Always Below 1 Ω
A62-23 (NSW) - B36-4 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR