Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) J

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  Brake Override System  


DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal sensor assembly and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A286034E02
1.917,2.958 2.844,3.531 0.927,0.573 10 Vehicle Speed 0.208,3.229 1.563,3.51 1.354,0.281 10 Wheel Speed Sensor 0.198,2.802 1.604,3.052 1.406,0.25 10 Vehicle Speed Sensor 0.188,2.177 1.354,2.5 1.167,0.323 10 Stop Light Switch 0.167,0.448 1.302,1.073 1.135,0.625 10 Accelerator Pedal Sensor Assembly 0.167,1.313 2.208,1.688 2.042,0.375 10 Master Cylinder Pressure Sensor (Brake Actuator Assembly) 2.313,1.427 3.302,1.76 0.99,0.333 10 Master Cylinder Pressure 0.792,3.021 0.948,3.323 0.156,0.302 10 or 3.51,0.552 3.854,0.802 0.344,0.25 10 ECM 4.917,0.958 6.969,1.583 2.052,0.625 10 Effective Accelerator Pedal Angle for System Control 1.948,2.302 2.521,2.604 0.573,0.302 10 ON/OFF 1.625,0.573 2.802,1.146 1.177,0.573 10 Actual Accelerator Pedal Angle 0.042,0.021 1.594,0.302 1.552,0.281 10 Brake Override System:

Activation Conditions:
·

Vehicle is running at or above the specified speed.

·

When the accelerator pedal and brake pedal are depressed.


NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



Items Controlled:
·

Driving torque is restricted.


HINT:

When this control is activated, the accelerator opening value is forcibly reduced to a fixed value. Therefore, the Accelerator Position value in the Data List is fixed regardless of the actual accelerator opening value (Accel Sens. No.1 Volt %).



Deactivation Conditions:
·

When the brake pedal or the accelerator pedal returns to some degree.



CAUTION / NOTICE / HINT

Inspection Method

Example:

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No.1 Volt % value. For more information on the numerical values, refer to the Data List.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

If the Accelerator Position and Accel Sens. No.1 Volt % values in the Data List diverge and the Accelerator Position value in the Data List is fixed even though Accel Sens. No.1 Volt % is changing, check that this control is activated (use the GTS snapshot function to record data while driving the vehicle, and then confirm it after driving is completed).



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: System Select / Health Check.


d.

Check the DTCs.

Result:
Result Proceed to
DTC is not output A
DTCs are output B




A

2.READ VALUE USING GTS (MASTER CYLINDER SENSOR)

B

GO TO DTC CHART

2.READ VALUE USING GTS (MASTER CYLINDER SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Master Cylinder Pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Pressure
50003 105 393

d.

Read the value displayed on the GTS.

GTS Display Measurement Item/Range Normal Condition
Master Cylinder Pressure Master cylinder pressure sensor reading/
Min.: 0.00 MPa, Max.: 23.28 MPa
·

Brake pedal released: 0.00 to 1.76 V

·

Reading increases when brake pedal is depressed




e.

Check that the brake fluid pressure value of the "Master Cylinder Pressure" observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the pressure displayed on the GTS increases.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1)

NG

3.READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

Powertrain > Engine and ECT > Data List
Tester Display
Stop Light Switch
ST1
50003 234 117,294

d.

Check the Data List indication when the brake pedal is depressed and released.

OK:
GTS Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON
ST1 Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

NG

4.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.

Inspect and adjust the brake pedal support assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

HINT:

If the stop light switch assembly turns on too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal support assembly and stop light switch assembly.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (ACCELERATOR PEDAL SENSOR)

NG

REPAIR OR REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

5.READ VALUE USING GTS (ACCELERATOR PEDAL SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 234 15,16

d.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Accel Sens. No.1 Volt % Accelerator Pedal
Released → Depressed → Released
Values smoothly change following accelerator pedal operation
Accel Sens. No.2 Volt %


HINT:

For numerical values of Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %, refer to the Data List.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

6.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR