The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU).
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
When replacing the combination meter assembly, make sure to replace it with a new one.
Check vehicle type.
| Proceed to |
|---|
| for Radio and Display Type |
| for Navigation Receiver Type |
| for Radio Receiver Type |
for Radio and Display Type
for Navigation Receiver Type
for Radio Receiver Type
*1: w/ Rain Sensor
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Entry and Start System
*4: for U660F
*5: for AD Series Engine
*6: except AD Series Engine
*7: for 11 Speakers
Disconnect the G16 combination meter assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.*1
Disconnect the A67 headlight leveling ECU assembly connector.*2
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3
Disconnect the B79 TCM connector.*4
Disconnect the A61*5 or A62*6 ECM connector.
Disconnect the M32 stereo component amplifier assembly connector.*7
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle except 11 speakers, proceed to next step.
*1: for Radio and Display Type
*2: for Navigation Receiver Type
*3: w/ Rain Sensor
*4: w/ Automatic Headlight Beam Level Control System
*5: w/ Entry and Start System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G143 radio and display receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G85 windshield wiper relay assembly connector.*3
Disconnect the A67 headlight leveling ECU assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle without a rain sensor, proceed to next step.
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Automatic Headlight Beam Level Control System
*5: w/ Entry and Start System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the A67 headlight leveling ECU assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle without an automatic headlight beam level control system, proceed to next step.
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Entry and Start System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle without an entry and start system, proceed to next step.
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Automatic Headlight Beam Level Control System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the A67 headlight leveling ECU assembly connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle except U660F, proceed to next step.
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Automatic Headlight Beam Level Control System
*6: w/ Entry and Start System
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the A67 headlight leveling ECU assembly connector.*5
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Automatic Headlight Beam Level Control System
*6: w/ Entry and Start System
*7: for U660F
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the A67 headlight leveling ECU assembly connector.*5
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6
Disconnect the B79 TCM connector.*7
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A80 brake actuator assembly (skid control ECU) connector.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A80-14 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
| *a | Component with harness connected
(Combination Meter Assembly) |
Connect an oscilloscope to terminal G16-5 (SI) and body ground.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | G16-5 (SI) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Driving at approximately 20 km/h (12 mph) |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Rain Sensor
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Entry and Start System
*4: for U660F
*5: for AD Series Engine
*6: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.*1
Disconnect the A67 headlight leveling ECU assembly connector.*2
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3
Disconnect the B79 TCM connector.*4
Disconnect the A61*5 or A62*6 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Rain Sensor
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Entry and Start System
*4: for U660F
*5: for AD Series Engine
*6: except AD Series Engine
*7: for 11 Speakers
Disconnect the G16 combination meter assembly connector.
Disconnect the G143 radio and display receiver assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.*1
Disconnect the A67 headlight leveling ECU assembly connector.*2
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3
Disconnect the B79 TCM connector.*4
Disconnect the A61*5 or A62*6 ECM connector.
Disconnect the M32 stereo component amplifier assembly connector.*7
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G143-17 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G143-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio and Display Type
*2: for Navigation Receiver Type
*3: w/ Rain Sensor
*4: w/ Automatic Headlight Beam Level Control System
*5: w/ Entry and Start System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the M32 stereo component amplifier assembly connector.
Disconnect the G143 radio and display receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G85 windshield wiper relay assembly connector.*3
Disconnect the A67 headlight leveling ECU assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - M32-11 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or M32-11 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Automatic Headlight Beam Level Control System
*5: w/ Entry and Start System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the A67 headlight leveling ECU assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G85-24 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G85-24 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Entry and Start System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the A67 headlight leveling ECU assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A67-16 (SPDR) | Always | Below 1 Ω |
| G16-6 (+S) or A67-16 (SPDR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Automatic Headlight Beam Level Control System
*6: for U660F
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the A67 headlight leveling ECU assembly connector.*5
Disconnect the B79 TCM connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A67-16 (SPDR) | Always | Below 1 Ω |
| G16-6 (+S) or A67-16 (SPDR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: w/ Rain Sensor
*5: w/ Automatic Headlight Beam Level Control System
*6: w/ Entry and Start System
*7: for AD Series Engine
*8: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the B79 TCM connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G139 navigation receiver assembly connector.*2
Disconnect the G143 radio and display receiver assembly connector.*3
Disconnect the G85 windshield wiper relay assembly connector.*4
Disconnect the A67 headlight leveling ECU assembly connector.*5
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6
Disconnect the A61*7 or A62*8 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - B79-3 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or B79-3 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for AD Series Engine
*2: except AD Series Engine
*3: for Radio Receiver Type
*4: for Navigation Receiver Type
*5: for Radio and Display Type
*6: w/ Rain Sensor
*7: w/ Automatic Headlight Beam Level Control System
*8: w/ Entry and Start System
*9: for U660F
Disconnect the G16 combination meter assembly connector.
Disconnect the A61*1 or A62*2 ECM connector.
Disconnect the G48 radio receiver assembly connector.*3
Disconnect the G139 navigation receiver assembly connector.*4
Disconnect the G143 radio and display receiver assembly connector.*5
Disconnect the G85 windshield wiper relay assembly connector.*6
Disconnect the A67 headlight leveling ECU assembly connector.*7
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*8
Disconnect the B79 TCM connector.*9
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A61-14 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or A61-14 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A62-57 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or A62-57 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A62-44 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or A62-44 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A62-57 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or A62-57 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
NG
Disconnect the G16 combination meter assembly connector.
Disconnect the A80 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-5 (SI) - A80-14 (SP1) | Always | Below 1 Ω |
| G16-5 (SI) or A80-14 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Rain Sensor
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Entry and Start System
*4: for U660F
*5: for AD Series Engine
*6: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G139 navigation receiver assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.*1
Disconnect the A67 headlight leveling ECU assembly connector.*2
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3
Disconnect the B79 TCM connector.*4
Disconnect the A61*5 or A62*6 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G139-17 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G139-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Rain Sensor
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Entry and Start System
*4: for U660F
*5: for AD Series Engine
*6: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.*1
Disconnect the A67 headlight leveling ECU assembly connector.*2
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3
Disconnect the B79 TCM connector.*4
Disconnect the A61*5 or A62*6 ECM connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Rain Sensor
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Entry and Start System
*4: for U660F
*5: for AD Series Engine
*6: except AD Series Engine
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.
Disconnect the G85 windshield wiper relay assembly connector.*1
Disconnect the A67 headlight leveling ECU assembly connector.*2
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3
Disconnect the B79 TCM connector.*4
Disconnect the A61*5 or A62*6 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G48-17 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G48-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG