Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check the radio automatic station search function by activating it.
Automatic station search function stops on a station.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Optional components are installed.
Do not remove optional components without permission of the customer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna connector from the navigation receiver assembly.
Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.
Turn on the radio and turn into AM mode.
Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise occurs.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the RA navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (ANT+) - Body ground | Engine switch on (ACC), radio switch on and FM or AM selected | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 1 amplifier antenna assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 1 | Always | Below 1 Ω |
| 1 - 3 | Always | Below 1 Ω |
| 2 - Body ground | Always | 10 kΩ or higher |
| 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | Below 1 Ω |
| 3 - 3 | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Navigation Receiver Assembly) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the navigation receiver assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - RA-3 (MAIN) | Always | Below 1 Ω |
| 3 - RA-5 (ANT+) | Always | Below 1 Ω |
| 2 - Body ground | Always | 10 kΩ or higher |
| 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Instrument Panel Side)>REMOVAL
Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG