Home › Engine / Hybrid System › 3ZR-FE ENGINE CONTROL › SFI SYSTEM(except K111, K111F) › from 2015.10
RM3090E _51 Engine / Hybrid System _008380 3ZR-FE ENGINE CONTROL _0219904 SFI SYSTEM(except K111, K111F) C

3ZR-FE ENGINE CONTROL  SFI SYSTEM(except K111, K111F)  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch assembly remains on. When the stop light switch assembly remains on during STOP and GO driving, the ECM interprets this as a fault in the stop light switch assembly. Then the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High The stop light switch remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic).
·

Short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch assembly remains on. When the stop light switch assembly remains on during "STOP and GO" driving, the ECM interprets this as a fault in the stop light switch assembly. The ECM turns on MIL and stores the DTC. The vehicle must STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) 5 times during 2 driving cycles, in order to detect a malfunction.

CONFIRMATION DRIVING PATTERN

A199312E59
1.427,2.021 1.771,2.219 0.344,0.198 10 false Idling 0.427,2.385 1.802,2.688 1.375,0.302 10 false Engine Switch on (IG) 2.51,2.5 2.708,2.698 0.198,0.198 10 false [A] 2.583,3.083 3.292,3.229 0.708,0.146 10 false 5 seconds 3.25,3.49 3.458,3.667 0.208,0.177 10 false [B] 3.406,1.896 3.615,2.073 0.208,0.177 10 false [C] 6.708,3.479 6.906,3.677 0.198,0.198 10 false [E] 4.042,1.5 4.25,1.677 0.208,0.177 10 false [D] 1.271,1.24 1.792,1.406 0.521,0.167 10 false 30 km/h 1.344,1.75 1.844,1.927 0.5,0.177 10 false 3 km/h

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0724.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].



12.

Start the engine [C].

13.

Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Using the GTS, the Data List item "Stop Light Switch" and "ST1" can be read.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(except K111, K111F)>DATA LIST / ACTIVE TEST



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Stop Light Switch.

Powertrain > Engine and ECT > Data List
Tester Display
Stop Light Switch
50003 234 117

e.

Read the values displayed on the GTS.

OK:
GTS Display Measurement Item/Range (display) Normal Condition
Stop Light Switch Stop light switch status: ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released





Result:
Proceed to
OK
NG



OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

OK:

Stop light switch is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A77-3 (L) - A62-9 (STP) Always Below 1 Ω
A77-3 (L) or A62-9 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY