Home › Engine / Hybrid System › 2WW LUBRICATION › OIL PUMP › from 2015.10
RM3090E _51 Engine / Hybrid System _044378 2WW LUBRICATION _0220674 OIL PUMP A

2WW LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 15115 1.INSTALL OIL PUMP COVER

a.
A318535C01
1.281,0.854 1.396,0.208 1.396,0.208 2,0.833 true 3,0.885 2.438,0.438 2.438,0.438 2.375,0.917 true 2.448,0.448 2.667,1.635 true 1.406,0.229 1.615,1.583 true 1.302,0.021 1.615,0.219 0.313,0.198 10 false *a 2.365,0.219 2.677,0.417 0.313,0.198 10 false *b
*a Hole
*b Protrusion


Align the protrusion of the oil pump cover with the hole of the oil pump with vacuum pump assembly and attach the claw to install the oil pump cover.


Hide 15163 2.INSTALL OIL PUMP DRIVE SHAFT GEAR

a.
A318533N01
1.188,0.427 1.427,0.25 1.427,0.25 1.563,0.25 false 1.625,0.177 2.083,0.375 0.458,0.198 10 false SST

Install the oil pump drive shaft gear with the bolt so that the front mark is as shown in the illustration.

HINT:

The bolt of the oil pump drive shaft gear is tightened in 2 progressive steps.



b.

Step 1:

i.

Using SST and a T45 "TORX" socket wrench, install the oil pump drive shaft gear with the bolt.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



c.

Step 2:

i.

Mark the top of the bolt with paint.


ii.

Tighten the bolt 90°.


iii.

Check that the paint mark is now at a 90° angle to the top.



Hide 3.INSTALL OIL PUMP WITH VACUUM PUMP ASSEMBLY

a.

Install the oil pump drive chain sub-assembly to the oil pump drive shaft gear, and then install the oil pump with vacuum pump assembly.


b.

Using an E10 "TORX" socket wrench, install the oil pump with vacuum pump assembly with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 15104 4.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install the oil strainer sub-assembly with the 2 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



Hide 12101 5.INSTALL OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.


b.
A318530

Apply seal packing to the oil pan sub-assembly as shown in the illustration.

Standard Seal Packing Diameter:

2.0 to 2.5 mm (0.0787 to 0.0984 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

After applying seal packing, install the oil pan sub-assembly within 3 minutes and tighten the bolts.




c.

Using an E10 "TORX" socket wrench, temporarily install the oil pan sub-assembly with the 24 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
A318523

Tighten the 20 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


e.

Tighten the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 6.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 51441 9.INSTALL NO. 1 ENGINE UNDER COVER