Home › Engine / Hybrid System › 2WW INTAKE / EXHAUST › INTAKE MANIFOLD › from 2015.10
RM3090E _51 Engine / Hybrid System _044376 2WW INTAKE / EXHAUST _0210931 INTAKE MANIFOLD A

2WW INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SWIRL CONTROL VALVE

a.

Install the swirl control valve with the 3 bolts to the intake manifold.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



b.

Attach the rod to the swirl control valve.


Hide 25612A 2.INSTALL NO. 2 EGR PIPE

a.

Install a new O-ring to the No. 2 EGR pipe.


b.

Install the No. 2 EGR pipe to the intake manifold.


Hide 28550 4.INSTALL GLOW PLUG CONTROLLER ASSEMBLY

Hide 17111 6.INSTALL INTAKE MANIFOLD

a.

Install a new gasket to the No. 2 EGR pipe.

HINT:

Make sure that the claw of the gasket faces the No. 2 EGR pipe.



b.

Install 4 new gaskets to the intake manifold.


c.
A337430C01
1.229,1.448 1.385,1.646 0.156,0.198 10 true 1 0.458,2.917 0.615,3.115 0.156,0.198 10 true 2 1.969,2.906 2.125,3.104 0.156,0.198 10 true 3 0.052,1.594 0.208,1.792 0.156,0.198 10 true 4 2.292,1.635 2.448,1.833 0.156,0.198 10 true 5
V100135

Bolt (A)
V100136

Bolt (B)


Temporarily install the intake manifold with the 7 bolts.


d.

Tighten the 5 bolts (A) in the order shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Further tighten the 5 bolts (A) in the order shown in the illustration again.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Tighten the 2 bolts (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 25733A 7.INSTALL NO. 1 VACUUM PIPE

a.

Install a new O-ring to the No. 1 vacuum pipe.


b.

Using an E7 "TORX" socket wrench, install the No. 1 vacuum pipe to the cylinder block sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the vacuum hose.


Hide 8.INSTALL NO. 2 VACUUM HOSE ASSEMBLY

a.

Connect the No. 2 vacuum hose assembly to the No. 1 vacuum pipe.

i.

Check that there is no damage or contamination in the connected part of the No. 1 vacuum pipe.


ii.

Line up the No. 1 vacuum pipe and No. 2 vacuum hose assembly connector and push them together until a "click" sound is heard. If the connection is tight, apply a small amount of clean engine oil to the tip of the No. 1 vacuum pipe.


iii.
A316719C01
0,0 0,0 false
V100135

Pull


After connecting the No. 1 vacuum pipe and No. 2 vacuum hose assembly connector, check that the No. 1 vacuum pipe and No. 2 vacuum hose assembly connector are securely connected by pulling on them.



Hide 11409 9.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the engine oil level dipstick guide.


b.

Using a T25 "TORX" socket wrench, install the engine oil level dipstick guide with the bolt.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



c.

Attach the clamp and connect the fuel feed pipe sub-assembly to the engine oil level dipstick guide.


d.

Install the engine oil level dipstick.


Hide 10.CONNECT ENGINE WIRE

a.

Using a T25 "TORX" socket wrench, connect the engine wire and install the screw.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



b.

Attach the 2 clamps.


c.

Connect the 2 glow plug controller assembly connectors.


d.

Connect the turbo pressure sensor assembly connector.


e.

Connect the camshaft position sensor connector.


f.

Connect the generator assembly connector.


g.

Connect the engine coolant temperature sensor connector.


h.

Connect the fuel pressure sensor connector.


i.

Connect the swirl control valve connector.


j.

Attach the 6 clamps and connect the fuel quantity control valve connector.


k.

Connect the EGR gas temperature sensor connector.


l.

Attach the 2 clamps and connect the glow plug controller assembly harness connector.


Hide 22030 12.INSTALL DIESEL THROTTLE BODY ASSEMBLY