Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E335235E05
0.979,0.542 2.052,0.75 1.073,0.208 10 false from TAIL Relay 3.458,0.719 4,0.938 0.542,0.219 10 false PANEL 6.021,1.688 6.344,1.875 0.323,0.188 10 false ILL+ 4.99,1.688 5.24,1.865 0.25,0.177 10 false G8 4.99,3.302 5.24,3.479 0.25,0.177 10 false G8 3.958,3.292 4.208,3.469 0.25,0.177 10 false z1 3.958,1.677 4.208,1.854 0.25,0.177 10 false z1 5.781,1.583 5.969,1.771 0.188,0.188 10 false 10 3.979,1.5 4.167,1.688 0.188,0.188 10 false 5 5.031,1.5 5.219,1.688 0.188,0.188 10 false 9 3.99,3.104 4.177,3.292 0.188,0.188 10 false 3 5,3.104 5.188,3.292 0.188,0.188 10 false 11 0.75,6.281 2.698,6.51 1.948,0.229 10 false Steering Pad Switch Assembly 0.625,5.823 2.573,6.052 1.948,0.229 10 false Steering Pad Switch RH Side 0.604,3.604 2.552,3.833 1.948,0.229 10 false Steering Pad Switch LH Side 4.417,1.802 4.74,1.99 0.323,0.188 10 false IL+2 4.406,3.406 4.771,3.594 0.365,0.188 10 false -DP 5.865,5.229 6.333,5.406 0.469,0.177 10 false G141 5.865,5.406 7.156,5.802 1.292,0.396 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E270420C28
0.208,0.781 0.563,1.01 0.354,0.229 2.083,2 1.833,2 1.833,2 1.698,1.542 true 1.323,1.552 1.219,2 1.219,2 0.969,2 true 0.677,1.917 1.063,2.104 0.385,0.188 10 false IL+2 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.292,0.802 0.604,1 0.313,0.198 10 false G8 2.156,1.906 2.479,2.104 0.323,0.198 10 false -DP
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


Disconnect the spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-11 (-DP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-9 (IL+2) - Body ground Ignition switch off Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E259248C24
1.51,0.396 1.896,0.594 0.385,0.198 2.271,1.656 2.083,1.354 false 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.531,0.417 1.875,0.625 0.344,0.208 10 false G141 2.198,1.708 2.75,1.927 0.552,0.219 10 false ILL+
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G141-10 (ILL+) - Body ground Ignition switch off Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR