Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Always

2.

Short in CVT fluid temperature sensor circuit

3.

0.5 seconds

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

10 seconds or more after starting engine (Engine coolant temperature and intake air temperature at engine start are higher than -29.375°C (-20.875°F))

2.

Open in CVT fluid temperature sensor circuit

3.

0.5 seconds

4.

1-trip detection logic


DTC Detection Condition 2:
1.

15 minutes or more after starting engine (Engine coolant temperature and intake air temperature at engine start are at -29.375°C (-20.875°F) or less)

2.

Open in CVT fluid temperature sensor circuit

3.

0.5 seconds

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects an open or short circuit in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is below 79 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the CVT fluid sensor or wiring. The ECM illuminates the MIL and stores a DTC.

*1: 150°C (302°F) or higher is indicated regardless of the actual CVT fluid temperature.

*2: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked on the GTS display.


WIRING DIAGRAM

C298187E06
0.771,3.208 4.177,3.531 3.406,0.323 10 false Continuously Variable Transaxle Assembly 1.792,2.76 3.031,2.979 1.24,0.219 10 false Transmission Wire 1.802,2.604 2.26,2.802 0.458,0.198 10 false B105 1.531,1.719 5.813,1.917 4.281,0.198 10 false CVT Fluid Temperature Sensor 5.615,1.25 6.229,1.448 0.615,0.198 10 false THO1 5.615,2.219 6.229,2.417 0.615,0.198 10 false ETHO 5.26,2.104 5.719,2.302 0.458,0.198 10 false 130 5.26,1.125 5.719,1.323 0.458,0.198 10 false 129 3.531,1.135 4.146,1.333 0.615,0.198 10 false THO 3.625,2.104 4.24,2.302 0.615,0.198 10 false E2 3.927,1.125 4.385,1.323 0.458,0.198 10 false 1 3.927,2.115 4.385,2.313 0.458,0.198 10 false 7 5.813,3.208 6.271,3.406 0.458,0.198 10 false B93 5.823,3.385 6.281,3.583 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE 1)
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


f.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall speed test: approximately 100°C (212°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted.
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
a.
C298188C07
2.813,0.563 2.396,0.917 true 2.833,1.552 2.396,1.281 true 2.865,0.49 3.323,0.688 0.458,0.198 10 false THO 2.906,1.51 3.365,1.708 0.458,0.198 10 false E2 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 7 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground and other terminals Always 10 kΩ or higher
7 (E2) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is outside the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may be affected.

CVT Fluid Temperature Specified Condition
10°C (50°F) 5.6 to 7.3 kΩ
25°C (77°F) 3.5 kΩ
110°C (230°F) 0.22 to 0.27 kΩ



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C06
1.427,0.198 1.813,0.427 0.385,0.229 1.521,1.698 1.844,1.156 true 2.281,1.719 1.906,1.156 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.229,1.74 1.99,1.958 0.76,0.219 10 false 129 (THO1) 1.51,0.24 1.969,0.438 0.458,0.198 10 false B93 2.083,1.75 2.844,1.969 0.76,0.219 10 false 130 (ETHO)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-129 (THO1) - B93-130 (ETHO) Always 79 Ω to 156 kΩ
B93-129 (THO1) - Body ground and other terminals Always 10 kΩ or higher
B93-130 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT