Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0172311 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of continuously variable transaxle assembly
·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminated)

·

Deterioration of fuel efficiency


(Click here)


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The engine assembly with continuously variable transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


Hide 11361J 2.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C297722

Remove the flywheel housing under cover.


Hide 32101G 3.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C299092N01
1.427,1.708 2.26,0.583 2.26,0.583 2.625,0.583 false 1.75,1.979 2.25,0.583 false 2.688,0.521 3.146,0.719 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-54015  
09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-00850 (quantity: 2)



b.
C300744

Remove the 6 drive plate and torque converter assembly setting bolts.


Hide 16267J 5.DISCONNECT NO. 3 WATER BY-PASS HOSE

a.
C315507

Slide the clip and disconnect the No. 3 water by-pass hose from the oil cooler.


Hide 16282 6.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
C315508

Slide the clip and disconnect the No. 5 water by-pass hose from the oil cooler.


b.

Disconnect the No. 5 water by-pass hose from the 2 clamps.


Hide 82121 7.DISCONNECT ENGINE WIRE

a.
C295565

Disconnect the 5 connectors and detach the 4 clamps.


b.

Remove the bolt and disconnect the engine wire.


c.
C295566

Disconnect the 2 connectors and detach the 2 clamps.


d.

Remove the 2 bolts and nut disconnect the engine wire.


Hide 35141D 8.DISCONNECT BREATHER PLUG HOSE

a.
C296768

Disconnect the breather plug hose from the clamp.


Hide 12311A 10.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C328294

Remove the 3 bolts and front engine mounting bracket from the continuously variable transaxle assembly.


Hide 12321A 11.REMOVE REAR ENGINE MOUNTING BRACKET

a.
C295574

Remove the 4 bolts and rear engine mounting bracket from the continuously variable transaxle assembly.


Hide 12325A 12.REMOVE ENGINE MOUNTING BRACKET LH

a.
C295569

Remove the 6 bolts, engine mounting bracket LH and engine mounting stay LH from the continuously variable transaxle assembly.


Hide 43457 14.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 36100 15.REMOVE TRANSFER ASSEMBLY

Hide 30400 16.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C295575

Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



Hide 32000A 17.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400B 18.REMOVE CVT TYPE T OIL SEAL

CAUTION:
·

Do not remove the front oil pump assembly from the continuously variable transaxle assembly main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a continuously variable transaxle assembly malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the continuously variable transaxle assembly.

·

Do not use cotton work gloves, cloths, paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter may enter the continuously variable transaxle assembly while the torque converter assembly is not attached to it.

·

Do not use an air gun until the torque converter assembly has been installed, as it may cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C208788C02
2.406,2.073 2.406,2.604 false 0.979,1.25 1.302,0.781 1.302,0.781 1.563,0.781 false 1.802,2.531 1.542,2.531 1.542,2.531 1.271,1.865 false 2.302,2.646 2.76,2.844 0.458,0.198 10 false SST 1.604,0.677 1.99,1.104 0.385,0.427 10 false *1 1.844,2.417 2.271,2.833 0.427,0.417 10 false *a
*1 CVT Type T Oil Seal
*a Claw


Using SST, remove the CVT type T oil seal from the continuously variable transaxle assembly.

NOTICE:

Pay attention to the angle of the claws of SST when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles may be produced if they do.



Hide 33823 19.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C295568

Disconnect the clamp from the No. 1 transmission control cable bracket.


b.

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 33829 20.REMOVE TRANSMISSION CONTROL CABLE SUPPORT

a.
C315509

Remove the 2 bolts and transmission control cable support from the continuously variable transaxle assembly.


Hide 21.REMOVE WIRE HARNESS CLAMP BRACKET

C295567C03
1.188,1.135 1.604,1.135 true 0.896,0.531 0.729,0.365 0.729,0.365 0.531,0.365 true 1.417,3.125 1.417,2.823 true 6.271,1.99 6.594,1.99 true 5.99,4.323 6.448,4.323 true 1.667,1.063 1.979,1.26 0.313,0.198 10 true *3 0.375,0.281 0.688,0.479 0.313,0.198 10 false *2 1.354,3.156 1.667,3.354 0.313,0.198 10 true *1 6.635,1.917 6.948,2.115 0.313,0.198 10 false *1 6.51,4.26 6.823,4.458 0.313,0.198 10 true *1
*1 Wire Harness Clamp Bracket *2 Water By-pass Hose Clamp
*3 Water Hose Clamp Bracket - -


a.

Remove the bolt and water hose clamp bracket from the continuously variable transaxle assembly.


b.

Remove the water by-pass hose clamp from the water hose clamp bracket.


c.

Remove the 3 bolts and 3 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 32921P 22.REMOVE OIL COOLER TUBE UNION

a.
C296963

Slide the clip and disconnect the No. 1 transmission oil cooler hose from the oil cooler tube union.

NOTICE:

Do not damage the coating of the hose insertion part of the oil cooler tube union.



b.

Remove the oil cooler tube union from the continuously variable transaxle assembly.


c.

Remove the O-ring from the oil cooler tube union.


Hide 32901F 23.REMOVE OIL COOLER ELBOW SUB-ASSEMBLY

a.
C296964

Slide the clip and disconnect the No. 2 transmission oil cooler hose from the oil cooler elbow sub-assembly.

NOTICE:

Do not damage the coating of the hose insertion part of the oil cooler elbow sub-assembly.



b.

Remove the union bolt, oil cooler elbow sub-assembly and gasket from the continuously variable transaxle assembly.


Hide 35125A 24.REMOVE TRANSMISSION OIL FILLER TUBE STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the transmission oil filler tube straight screw plug is necessary.


a.
C316583

Remove the transmission oil filler tube straight screw plug and gasket from the continuously variable transaxle assembly.


Hide 35141D 25.REMOVE BREATHER PLUG HOSE

HINT:

Perform this procedure only when replacement of the breather plug hose is necessary.


NOTICE:

When replacing the continuously variable transaxle assembly, be sure to install the breather plug hose.


a.
C295577C01
2.51,0.51 2.875,0.51 false 2.938,0.438 3.25,0.635 0.313,0.198 10 false *1
*1 Breather Plug Hose


Remove the breather plug hose from the continuously variable transaxle assembly.


b.
C330783C01
2.01,1.406 2.573,1.406 false 1.698,1.854 2.292,1.854 false 1.469,0.667 2.156,0.667 false 2.646,1.323 2.958,1.521 0.313,0.198 10 false *1 1.531,1.771 1.844,1.969 0.313,0.198 10 false *2 2.24,0.563 2.552,0.76 0.313,0.198 10 false *3
*1 Breather Plug
*2 O-ring
*3 Breather Plug Hose


Remove the breather plug from the breather plug hose.


c.

Remove the O-ring from the breather plug.


Hide 35151K 26.REMOVE AUTOMATIC TRANSMISSION CASE COVER

a.
C297207

Remove the 2 clips and automatic transmission case cover from the continuously variable transaxle assembly.


Hide 36100A 27.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Transfer side:

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>REMOVAL


a.
C269868

Remove the 2 transfer and transaxle setting stud bolts.


Hide 32000A 28.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 29.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY