Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0842  Transmission Fluid Pressure Sensor/Switch "A" Circuit Low  P0843  Transmission Fluid Pressure Sensor/Switch "A" Circuit High  


DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0842 Transmission Fluid Pressure Sensor/Switch "A" Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

2 seconds or more after engine start

2.

Short in oil pressure sensor circuit

3.

0.5 seconds

4.

1-trip detection logic


·

Harness or connector

·

Oil pressure sensor

·

ECM


Comes on (w/ OBD)
Does not come on (w/o OBD)
DTC stored
P0843 Transmission Fluid Pressure Sensor/Switch "A" Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

2 seconds or more after engine start

2.

Open or short to B+ in oil pressure sensor circuit

3.

0.5 seconds

4.

1-trip detection logic


·

Harness or connector

·

Oil pressure sensor

·

ECM


Comes on (w/ OBD)
Does not come on (w/o OBD)
DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the oil pressure sensor. If there is an open or short in the oil pressure sensor circuit, the ECM detects the problem and stores a DTC.

WIRING DIAGRAM

C277073E06
1.375,2.896 4.281,3.094 2.906,0.198 10 false Oil Pressure Sensor 1.385,2.698 1.844,2.896 0.458,0.198 10 false B32 2.427,1.25 2.885,1.448 0.458,0.198 10 false VC 2.344,1.729 2.802,1.927 0.458,0.198 10 false PTO 2.438,2.219 2.896,2.417 0.458,0.198 10 false E2 5.615,1.25 6.073,1.448 0.458,0.198 10 false VCPT 5.615,1.729 6.073,1.927 0.458,0.198 10 false PTO 5.615,2.219 6.073,2.417 0.458,0.198 10 false EPTO 5.823,2.948 6.281,3.146 0.458,0.198 10 false B93 5.833,3.125 6.292,3.323 0.458,0.198 10 false ECM 5.25,1.135 5.708,1.333 0.458,0.198 10 false 110 5.323,1.615 5.781,1.813 0.458,0.198 10 false 79 5.25,2.104 5.708,2.302 0.458,0.198 10 false 109 2.74,1.135 3.198,1.333 0.458,0.198 10 false 3 2.74,1.615 3.198,1.813 0.458,0.198 10 false 2 2.75,2.104 3.208,2.302 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:

The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
3ZR-FAE:
·

3.5 to 4.5 MPa (35.7 to 45.9 kgf/cm2, 508 to 653 psi): D position stall speed test

·

2.5 to 4.5 MPa (25.5 to 45.9 kgf/cm2, 363 to 653 psi): R position stall speed test

·

0.140 to 0.400 MPa (1.4 to 4.1 kgf/cm2, 20 to 58 psi): With shift lever in D, engine is stopped by start and stop system (oil pump assembly with motor is operating)


3ZR-FE:
·

3.1 to 4.5 MPa (31.6 to 45.9 kgf/cm2, 450 to 653 psi): D position stall speed test

·

2.1 to 4.5 MPa (21.4 to 45.9 kgf/cm2, 305 to 653 psi): R position stall speed test


-
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)

B

6.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)
a.

Disconnect the B32 oil pressure sensor connector.


b.

Disconnect the B93 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B32-1 (E2) - B93-109 (EPTO) Always Below 1 Ω
B32-2 (PTO) - B93-79 (PTO) Always Below 1 Ω
B32-3 (VC) - B93-110 (VCPT) Always Below 1 Ω
B32-1 (E2) or B93-109 (EPTO) - Body ground and other terminals Always 10 kΩ or higher
B32-2 (PTO) or B93-79 (PTO) - Body ground and other terminals Always 10 kΩ or higher
B32-3 (VC) or B93-110 (VCPT) - Body ground and other terminals Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B93-79 (PTO) - Body ground Ignition switch ON Below 1 V
B32-2 (PTO) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (VCPT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PRESSURE SENSOR - ECM)

3.CHECK ECM (VCPT TERMINAL VOLTAGE)
a.
C125747C31
0.438,0.938 0.802,1.219 0.365,0.281 1.479,1.271 1.146,1.719 1.146,1.719 1.01,1.719 true 2.052,1.26 2.406,1.677 2.406,1.677 2.531,1.677 true 0.792,1.635 1.177,1.844 0.385,0.208 10 false E2 2.604,1.604 2.875,1.792 0.271,0.188 10 false VC 0.094,0.094 0.313,0.25 0.219,0.156 10 false *a 0.51,1.01 0.948,1.188 0.438,0.177 10 false B32
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B32-3 (VC) - B32-1 (E2) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

4.REPLACE OIL PRESSURE SENSOR

NG

5.REPLACE ECM
4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT