Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2769  Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  P2770  Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  


DESCRIPTION

Based on the signal received by the shift solenoid valve SL, the ECM uses the shift solenoid valve SLU to control the lock-up clutch pressure.

If there is an open or short in the shift solenoid valve SL circuit, the ECM stops sending current to the defective shift solenoid valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2769 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Lock-up is operating.

2.

A short in the shift solenoid valve SL circuit is detected.

3.

Detected 1 time or more consecutively

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SL)

·

ECM


Comes on DTC stored
P2770 Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Lock-up is operating.

2.

An open in the shift solenoid valve SL circuit is detected.

3.

Detected 1 time or more consecutively

4.

1-trip detection logic


·

Harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SL)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SL circuit. If there is an open or short in the shift solenoid valve SL circuit, the ECM detects the problem, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

C264610E49
0.781,2.083 2.333,2.229 1.552,0.146 10 false Shift Solenoid Valve SL 0.917,2.833 3.542,3.271 2.625,0.438 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 6.146,2.781 6.51,3.01 0.365,0.229 10 false ECM 0.938,2.646 1.365,2.823 0.427,0.177 10 false B105 5.813,1.021 6.354,1.302 0.542,0.281 10 false SL 5.813,1.865 6.229,2.052 0.417,0.188 10 false E1 5.531,0.896 5.708,1.156 0.177,0.26 10 false 67 5.531,1.74 5.896,1.885 0.365,0.146 10 false 59 4.75,0.896 5,1.063 0.25,0.167 10 false 12 6.146,2.604 6.604,2.875 0.458,0.271 10 false B93 4.479,0.885 4.865,1.167 0.385,0.281 10 false SL

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C298188C10
0.885,1.771 1.25,1.281 true 0.698,1.74 1.156,1.938 0.458,0.198 10 false SL 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C05
1.427,0.198 1.813,0.427 0.385,0.229 0.552,1.719 0.729,1.021 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.365,1.76 1.125,1.979 0.76,0.219 10 false 67 (SL) 1.51,0.24 1.969,0.438 0.458,0.198 10 false B93
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-67 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT