Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0104513 NAVIGATION SYSTEM(for SD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the engine switch is on (ACC), 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more.
·

Combination meter assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E268494E61
1.604,0.427 2.219,0.625 0.615,0.198 10 false MSCH 1.635,1.063 2.25,1.26 0.615,0.198 10 false MSCL 5.083,0.427 5.698,0.625 0.615,0.198 10 false CNH1 5.094,1.083 5.708,1.281 0.615,0.198 10 false CNL1 2.146,0.292 2.76,0.49 0.615,0.198 10 false 23 2.146,0.938 2.76,1.135 0.615,0.198 10 false 22 4.906,0.292 5.521,0.49 0.615,0.198 10 false 3 4.906,0.927 5.521,1.125 0.615,0.198 10 false 4 0.781,1.594 1.396,1.792 0.615,0.198 10 false G16 0.781,1.75 2.75,1.979 1.969,0.229 10 false Combination Meter Assembly 4.781,1.583 5.396,1.781 0.615,0.198 10 false G158 4.781,1.74 6.75,1.969 1.969,0.229 10 false Navigation Receiver Assembly 0.906,2.219 3.271,2.448 2.365,0.229 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G158 navigation receiver assembly connector.


b.

Disconnect the G16 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G158-3 (CNH1) - G16-23 (MSCH) Always Below 1 Ω
G158-4 (CNL1) - G16-22 (MSCL) Always Below 1 Ω
G158-3 (CNH1) - Body ground Always 10 kΩ or higher
G158-4 (CNL1) - Body ground Always 10 kΩ or higher
G158-3 (CNH1) - G158-4 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G158-3 (CNH1) - Body ground Always Below 1 V
G158-4 (CNL1) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.

Remove the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.
E317642N02
2.26,1.813 2.406,1.813 2.406,1.813 2.635,1.344 true 2.813,1.833 2.688,1.833 2.688,1.833 2.771,1.344 true 1.802,1.719 2.417,1.917 0.615,0.198 10 false MSCH 2.865,1.74 3.323,1.927 0.458,0.188 10 false MSCL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
23 (MSCH) - 22 (MSCL) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E317643N01
1.333,1.875 1.5,1.875 1.5,1.875 2.104,1.177 true 2.354,1.875 2.146,1.875 2.146,1.875 2.25,1.177 true 2.417,1.792 3.031,1.99 0.615,0.198 10 false CNH1 0.958,1.792 1.573,1.99 0.615,0.198 10 false CNL1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

5.CHECK METER / GAUGE SYSTEM

NG

5.CHECK METER / GAUGE SYSTEM
a.

Turn the engine switch on (IG) and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG