Home › Engine / Hybrid System › 2WW FUEL › FUEL SUPPLY PUMP › from 2015.10
RM3090E _51 Engine / Hybrid System _044374 2WW FUEL _0221820 FUEL SUPPLY PUMP A

2WW FUEL  FUEL SUPPLY PUMP  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After the engine has stopped, wait at least 1 minute before releasing the high pressure lines.

·

When working on the fuel circuit, protect the generator assembly against contamination. Cover the generator assembly with suitable materials. Failure to comply with this procedure may result in a generator assembly malfunction.

·
A316354N01
2.656,0.188 0.958,0.188 0.958,0.188 0.958,0.417 false 2.375,0.406 2.375,0.188 false 2.74,0.104 3.198,0.302 0.458,0.198 10 false SST

After disconnecting the pressure line, it is absolutely essential to seal the injector assemblies and the common rail assembly with SST.

SST:

PZ4TB-04941-79


·

The position of the fuel supply pump assembly in relation to the valve gear does not affect its function. However, it must be taken into account during removal and installation.



Hide 2.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 3.SET NO. 1 CYLINDER TO TDC/COMPRESSION

NOTICE:

Set the No. 1 cylinder to TDC/compression so that the fuel supply pump assembly can be removed.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Hide 23292A 4.REMOVE NO. 1 AND NO. 2 FUEL HOSE PROTECTOR

a.
A362708

Detach the clamp to disconnect the fuel temperature sensor connector.


b.

Remove the bolt and No. 1 fuel hose protector from the No. 2 fuel hose protector.


c.
A362709

Remove the No. 2 fuel hose protector from the fuel feed line hose and fuel return line hose.


Hide 22100 5.REMOVE FUEL SUPPLY PUMP ASSEMBLY

NOTICE:

Do not remove SST A from the injection pump drive gear until all repair work has been completed.


a.
A316272C01
0.521,1.719 0.698,1.719 0.698,1.719 1.094,1.427 true 1.875,2 1.875,1.698 true 1.792,2.021 2.104,2.177 0.313,0.156 10 false *1 0.333,1.646 0.646,1.802 0.313,0.156 10 false *2
*1 Fuel Feed Line Hose
*2 Fuel Return Line Hose


Disconnect the fuel quantity control valve connector.


b.

Loosen the 2 clamps and disconnect the fuel feed line hose and fuel return line hose from the fuel supply pump assembly.


c.

Remove the 2 clamps from the fuel feed line hose and fuel return line hose.


d.
A316273

Remove the sealing cap from the timing chain cover plate.


e.

Remove the O-ring from the sealing cap.


f.
A316274N01
1.229,0.417 1.375,0.417 1.375,0.417 1.573,0.76 true 1.229,1.802 1.375,1.802 1.375,1.802 1.646,1.292 true 0.76,0.344 1.208,0.542 0.448,0.198 10 true SST A 0.771,1.729 1.219,1.927 0.448,0.198 10 false SST B

Using SST B, install SST A to position the fuel supply pump assembly. Then remove SST B.

SST:

PZ4TB-04967-25


NOTICE:

Do not remove SST A from the timing chain cover plate until all repair work has been completed.



g.
A316275

Remove the 4 bolts and fuel supply pump assembly support.


h.
A316276

Remove the 2 bolts from the fuel supply pump assembly.


i.
A316277C01
1.833,1.042 1.979,0.625 1.979,0.625 2.146,0.625 true 2.198,0.542 2.656,0.74 0.458,0.198 10 true SST A

Loosen the central bolt connection between the fuel supply pump assembly and injection pump drive gear.

NOTICE:
·

Do not remove SST A from the timing chain cover plate.

·

The central bolt is supported on SST A until the fuel supply pump assembly is pressed out.

·
A316352C03
1.688,0.906 2.083,0.417 2.083,0.417 2.333,0.417 true 2.031,1 2.448,1 true 2.396,0.344 2.708,0.542 0.313,0.198 10 false *1 2.5,0.938 3.271,1.135 0.771,0.198 10 false SST A
*1 Central Bolt


The central bolt remains inside SST A attached to the injection pump drive gear.




j.

Remove the fuel supply pump assembly from the cylinder block.


k.

Remove the 2 bolts and fuel quantity control valve.