Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › from 2015.10
RM3090E _52 Drivetrain _008760 GF1A TRANSFER / 4WD / AWD _0048749 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM D

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


Dynamic torque control 4WD/AWD system data can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform repairs. Therefore when there seems to be a problem with the dynamic torque control 4WD/AWD system, use the GTS or SST to check and troubleshoot it.


CHECK DATA LINK CONNECTOR 3 (DLC3)




FUNCTION OF 4WD/AWD WARNING LIGHT


a.

for Segment Display Type:

The 4WD/AWD warning light in the combination meter warns the driver of abnormal or poor condition of the dynamic torque control 4WD/AWD system.

for TFT Display Type:

The 4WD/AWD warning message displayed on the multi-information display warns the driver of abnormal or poor condition of the dynamic torque control 4WD/AWD system.


b.

for Segment Display Type:

If the 4WD ECU assembly detects a malfunction, the 4WD/AWD warning light comes on in accordance with the trouble area to warn the driver.

for TFT Display Type:

If the 4WD ECU assembly detects a malfunction, the check master warning light comes on and the multi-information display displays warning messages in accordance with the trouble area to warn the driver.

HINT:

Check that the master warning light comes on for approximately 4 seconds.




CHECK WARNING LIGHT AND INDICATOR LIGHT


a.

Check warning and indicator lights.

i.

When the ignition switch is turned to ON, check that the 4WD/AWD warning*1, sport mode indicator*2 and 4WD/AWD lock mode indicator lights come on and go off within approximately 4 seconds.

*1: for Segment Display Type

*2: for Manual Transaxle


HINT:

If the warning and indicator lights do not illuminate, check for combination meter assembly and CAN communication system DTCs, since the 4WD ECU assembly and combination meter assembly are connected by the CAN communication line.

If the warning light remains on, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.




b.

Check 4WD/AWD warning (for TFT Display Type).

i.
C166029C49
0.135,1.01 0.563,1.313 0.427,0.302 1.635,0.875 1.854,0.313 false 1.979,1.875 1.813,1.427 false 1.823,0.135 2.188,0.313 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a 0.208,1.073 0.531,1.25 0.323,0.177 10 G14 1.885,1.875 2.25,2.052 0.365,0.177 10 TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 (to enter diagnostic mode).

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

"DIAG 4WD" or "DIAG AWD" is displayed on the multi-information display, and the 4WD ECU assembly checks the system for malfunctions.

·

If the dynamic torque control AWD system is normal, "DIAG 4WD FF" or "DIAG AWD FF"is displayed on the multi-information display.

·

If the dynamic torque control AWD system is not normal, "DIAG 4WD XX (DTC)" or "DIAG AWD XX (DTC)" is displayed on the multi-information display.

·

Although the test mode is not set for the dynamic torque control 4WD/AWD system, the message is displayed on the multi-information display when the test mode is activated for checking the VSC, etc.


HINT:
·

Test mode DTCs will not be stored because the test mode is not set.

·

If the systems above are not displayed on the multi-information display, there may be a malfunction in "TC and CG Terminal Circuit".

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>TC and CG Terminal Circuit

·

If the 4WD/AWD warning check result is not normal, proceed to troubleshooting for the 4WD/AWD warning light circuit.






Trouble Area See procedure
4WD/AWD warning light (Remains on) (Click here)
4WD/AWD warning light (Does not come on) (Click here)
4WD/AWD lock indicator light (Does not come on) (Click here)
Sport mode indicator light (Does not come on)* (Click here)

*: for Manual Transaxle