Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050373 BACK DOOR CLOSER SYSTEM C

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  B2250  Back Door Closer Operation Malfunction  


DESCRIPTION

The multiplex network door ECU receives signals from the latch switch, sector switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock assembly is determined.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2250 Back Door Closer Operation Malfunction While the back door closer is operating, a malfunction is detected in position information from the sector switch within a specified amount of time.
·

Back door lock assembly

·

Harness or connector

·

Multiplex network door ECU



WIRING DIAGRAM

B427347E02
5.083,5.823 7.042,6.406 1.958,0.583 10 false Multiplex Network Door ECU 5.375,0.74 5.99,1.073 0.615,0.333 10 false IG 5.375,1.219 5.99,1.552 0.615,0.333 10 false ECUB 5.385,1.708 6,2.042 0.615,0.333 10 false B 2.5,2.24 3.115,2.573 0.615,0.333 10 false M+ 5.375,2.865 5.99,3.198 0.615,0.333 10 false DC- 5.375,3.781 5.99,4.115 0.615,0.333 10 false HAF 5.385,4.281 6,4.615 0.615,0.333 10 false POS 5.396,3.26 6.01,3.594 0.615,0.333 10 false PAWL 5.375,4.76 5.99,5.094 0.615,0.333 10 false FUL 2.5,2.75 3.115,3.083 0.615,0.333 10 false M- 2.406,3.656 3.021,3.99 0.615,0.333 10 false CLS 2.375,4.177 2.99,4.51 0.615,0.333 10 false OPN 2.385,3.146 3,3.479 0.615,0.333 10 false FSW 2.385,4.667 3,5 0.615,0.333 10 false CTY 2.563,5.146 3.177,5.479 0.615,0.333 10 false E 0.76,4.885 2.719,5.469 1.958,0.583 10 false Back Door Courtesy Switch 0.99,3.427 2.219,3.813 1.229,0.385 10 false Pawl Switch 1.01,4.385 2.24,4.771 1.229,0.385 10 false Sector Switch 1.042,3.896 2.271,4.281 1.229,0.385 10 false Latch Switch 5.375,5.292 5.99,5.625 0.615,0.333 10 false GND 3.156,0.885 4.385,1.271 1.229,0.385 10 false ECU-IG NO.2 3.156,1.375 4.385,1.76 1.229,0.385 10 false ECU-B NO.1 3.385,1.854 4.615,2.24 1.229,0.385 10 false PBD 0.323,0.708 2.292,1.115 1.969,0.406 10 false from IG1 NO.1 Relay 0.833,1.198 2.063,1.583 1.229,0.385 10 false from Battery 0.896,2.563 2.365,3.031 1.469,0.469 10 false Back Door Lock Motor 0.302,5.677 2.26,6.26 1.958,0.583 10 false Back Door Lock Assembly 1.563,7.688 5.469,8.26 3.906,0.573 10 false Instrument Panel Junction Block Assembly 0.458,8.083 4.365,8.656 3.906,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 1.115,7.333 1.729,7.667 0.615,0.333 10 false BCTY 5.365,2.344 5.979,2.677 0.615,0.333 10 false DC+ 5.094,3.552 5.708,3.885 0.615,0.333 10 false 9 5.021,5.26 7.156,5.531 2.135,0.271 10 false U30 5.042,0.542 5.656,0.875 0.615,0.333 10 false 18 5.083,1.031 5.698,1.365 0.615,0.333 10 false 20 5.094,1.5 5.708,1.833 0.615,0.333 10 false 1 5.115,2.167 5.729,2.5 0.615,0.333 10 false 4 5.115,2.677 5.729,3.01 0.615,0.333 10 false 3 5.052,4.563 5.667,4.896 0.615,0.333 10 false 11 5.115,4.052 5.729,4.385 0.615,0.333 10 false 7 5.063,3.073 5.677,3.406 0.615,0.333 10 false 13 5.063,5.104 5.677,5.438 0.615,0.333 10 false 10 2.781,3.229 7.156,3.573 4.375,0.344 10 false U27 2.854,2.167 3.469,2.5 0.615,0.333 10 false 2 2.833,2.667 3.448,3 0.615,0.333 10 false 1 2.844,3.573 3.469,3.906 0.625,0.333 10 false 3 2.865,4.073 3.479,4.406 0.615,0.333 10 false 6 2.833,3.083 3.448,3.417 0.615,0.333 10 false 2 2.854,4.573 3.469,4.906 0.615,0.333 10 false 4 2.854,5.104 3.469,5.438 0.615,0.333 10 false 1 2.438,7.292 3.052,7.625 0.615,0.333 10 false 3E 2.458,7.135 3.073,7.469 0.615,0.333 10 false 33 1.625,7.302 2.24,7.635 0.615,0.333 10 false A 1.604,7.146 2.219,7.479 0.615,0.333 10 false 20 2.781,2.844 7.156,3.188 4.375,0.344 10 false U26 2.781,2.344 7.156,2.688 4.375,0.344 10 false U26 2.781,3.729 7.156,4.073 4.375,0.344 10 false U27 2.781,4.24 7.156,4.583 4.375,0.344 10 false U27 2.781,4.75 7.156,5.094 4.375,0.344 10 false U27 2.781,5.271 7.156,5.615 4.375,0.344 10 false U27 5.031,3.24 7.156,3.51 2.125,0.271 10 false U29 5.031,3.75 7.156,4.021 2.125,0.271 10 false U29 5.031,4.26 7.156,4.531 2.125,0.271 10 false U29 5.031,4.771 7.156,5.042 2.125,0.271 10 false U29 5.031,1.208 7.156,1.479 2.125,0.271 10 false U29 5.031,0.74 7.156,1.01 2.125,0.271 10 false U29 5.021,2.865 7.156,3.135 2.135,0.271 10 false U30 5.021,2.354 7.156,2.625 2.135,0.271 10 false U30 5.021,1.688 7.156,1.958 2.135,0.271 10 false U30

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Closer Position SW Sector switch signal ON or OFF ON: Back door lock center gear in center position
OFF: Back door lock center gear not in center position
*: Refer to "CONSTRUCTION AND OPERATION"

*: Refer to "CONSTRUCTION AND OPERATION"

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>SYSTEM DESCRIPTION

Body Electrical > Back Door > Data List
Tester Display
Closer Position SW
50003 159 3
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY
2.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the U27 back door lock assembly connector.


b.

Disconnect the U29 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U27-6 (OPN) - U29-7 (POS) Always Below 1 Ω
U27-1 (E) - Body ground Always Below 1 Ω
U27-6 (OPN) or U29-7 (POS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR