This DTC is output when the multiplex network door ECU detects a malfunction in the motor built into the power back door unit assembly set LH or RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2220 | Back Door Motor Circuit | Motor malfunction detected in power back door unit assembly set LH or RH | ·
Multiplex network door ECU ·
Power back door unit assembly LH ·
Power back door unit assembly RH ·
Harness and connector |
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
Clear the DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2220 is not output |
| DTC B2220 is output |
DTC B2220 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B2220 is output
Disconnect the U30 multiplex network door ECU connector.
Disconnect the U21 power back door unit assembly set LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U30-7 (BD+) - U21-1 (BD+) | Always | Below 1 Ω |
| U30-6 (BD-) - U21-2 (BD-) | Always | Below 1 Ω |
| U30-7 (BD+) or U21-1 (BD+) - Body ground | Always | 10 kΩ or higher |
| U30-6 (BD-) or U21-2 (BD-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U30 multiplex network door ECU connector.
Disconnect the U20 power back door unit assembly set RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U30-8 (BD+2) - U20-1 (BD+2) | Always | Below 1 Ω |
| U30-9 (BD-2) - U20-2 (BD-2) | Always | Below 1 Ω |
| U30-8 (BD+2) or U20-1 (BD+2) - Body ground | Always | 10 kΩ or higher |
| U30-9 (BD-2) or U20-2 (BD-2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the power back door unit assembly set LH with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2220 is not output |
| DTC B2220 is output |
DTC B2220 is not output
DTC B2220 is output
Temporarily replace the power back door unit assembly set RH with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2220 is not output |
| DTC B2220 is output |
DTC B2220 is not output
DTC B2220 is output