Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050374 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Closed Using the Power Back Door Closer Switch  


DESCRIPTION

When the power back door cannot be closed using the door control switch assembly, either of the following may be malfunctioning: 1) door control switch assembly circuit or 2) multiplex network door ECU.

WIRING DIAGRAM

B165217E37
4.875,1.979 6.635,2.219 1.76,0.24 10 false U29 4.865,2.156 6.625,2.396 1.76,0.24 10 false Multiplex Network Door ECU 5.323,1.073 7.083,1.313 1.76,0.24 10 false BDDN 5.115,0.948 6.875,1.188 1.76,0.24 10 false 8 3.646,0.948 5.406,1.188 1.76,0.24 10 false 1 2.083,0.958 3.844,1.198 1.76,0.24 10 false 2 3.271,1.177 5.031,1.417 1.76,0.24 10 false CLS 2.271,1.177 4.031,1.417 1.76,0.24 10 false E 2.135,1.427 3.896,1.667 1.76,0.24 10 false U17 2.135,1.615 4.104,1.875 1.969,0.26 10 false Door Control Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Check the Data List to determine if the door control switch assembly functions properly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Close SW Door control switch assembly signal ON or OFF ON: Door control switch assembly pushed
OFF: Door control switch assembly not pushed
-
Body Electrical > Back Door > Data List
Tester Display
PBD Close SW
50003 159 8
OK:

The door control switch assembly functions as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
a.

Remove the door control switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CLOSER SWITCH>REMOVAL


b.

Inspect the door control switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CLOSER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the U17 door control switch assembly connector.


b.

Disconnect the U29 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U17-1 (CLS) - U29-8 (BDDN) Always Below 1 Ω
U17-2 (E) - Body ground Always Below 1 Ω
U17-1 (CLS) or U29-8 (BDDN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR