Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

*1: for Radio and Display Type

*2: for Navigation Receiver Type


The combination meter assembly receives a text data signal from the radio and display receiver assembly*1 or navigation receiver assembly*2 via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B150A Lost Communication with HMI-LAN After the combination meter assembly receives a registration information signal, which is sent by the radio and display receiver assembly*1 or navigation receiver assembly*2 when the ignition switch is ON, 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.
·

Harness or connector

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

Combination meter assembly



WIRING DIAGRAM

for Radio and Display Type


E295995E34
5.177,2.698 7.156,2.927 1.979,0.229 10 false G16 5.188,2.854 7.021,3.25 1.833,0.396 10 false Combination Meter Assembly 5.375,1.802 6.5,2.104 1.125,0.302 10 false MSCL 5.375,1.125 6.5,1.427 1.125,0.302 10 false MSCH 5.135,1.688 6.26,1.99 1.125,0.302 10 false 22 5.104,1.021 6.229,1.323 1.125,0.302 10 false 23 1.125,3.396 2.885,3.708 1.76,0.313 10 false : CAN Communication Line 0.604,2.698 2.323,3.01 1.719,0.313 10 false G159 0.604,2.854 3.146,3.292 2.542,0.438 10 false Radio and Display Receiver Assembly 1.469,1.156 2.021,1.542 0.552,0.385 10 false CNH1 1.938,1 3.063,1.302 1.125,0.302 10 false 3 1.938,1.677 3.063,1.979 1.125,0.302 10 false 4 1.469,1.844 2.021,2.229 0.552,0.385 10 false CNL1


for Navigation Receiver Type


E295995E33
5.177,2.698 7.156,2.927 1.979,0.229 10 false G16 5.188,2.854 7.021,3.25 1.833,0.396 10 false Combination Meter Assembly 5.375,1.802 6.5,2.104 1.125,0.302 10 false MSCL 5.375,1.125 6.5,1.427 1.125,0.302 10 false MSCH 5.135,1.688 6.26,1.99 1.125,0.302 10 false 22 5.104,1.021 6.229,1.323 1.125,0.302 10 false 23 1.125,3.396 2.885,3.708 1.76,0.313 10 false : CAN Communication Line 0.604,2.698 2.323,3.01 1.719,0.313 10 false G158 0.604,2.854 3.146,3.292 2.542,0.438 10 false Navigation Receiver Assembly 1.469,1.156 2.021,1.542 0.552,0.385 10 false CNH1 1.938,1 3.063,1.302 1.125,0.302 10 false 3 1.938,1.677 3.063,1.979 1.125,0.302 10 false 4 1.469,1.844 2.021,2.229 0.552,0.385 10 false CNL1


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

except 8 Speakers:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for navigation system or audio and visual system.

Audio and Visual System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION

Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PRECAUTION

·

After replacing the radio receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Navigation System A
for Radio and Display Type B



A

2.CHECK FOR DTC (NAVIGATION SYSTEM)

B

5.CHECK FOR DTC (AUDIO AND VISUAL SYSTEM)
2.CHECK FOR DTC (NAVIGATION SYSTEM)
a.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G158 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-23 (MSCH) - G158-3 (CNH1) Always Below 1 Ω
G16-22 (MSCL) - G158-4 (CNL1) Always Below 1 Ω
G16-23 (MSCH) or G158-3 (CNH1) - Body ground Always 10 kΩ or higher
G16-22 (MSCL) or G158-4 (CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the ignition switch to ON and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.



c.
E274321C03
1.865,0.708 1.865,0.396 false 1.771,0.229 2.083,0.427 0.313,0.198 10 false *b 0.313,0.229 0.625,0.427 0.313,0.198 10 false *a
*a Multi-information Display
*b Audio Tab


Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

The audio tab illuminates and DTC B150A is not output.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

5.CHECK FOR DTC (AUDIO AND VISUAL SYSTEM)
a.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G159 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-23 (MSCH) -G159-3 (CNH1) Always Below 1 Ω
G16-22 (MSCL) - G159-4 (CNL1) Always Below 1 Ω
G16-23 (MSCH) or G159-3 (CNH1) - Body ground Always 10 kΩ or higher
G16-22 (MSCL) or G159-4 (CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the ignition switch to ON and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.



c.
E274321C03
1.865,0.708 1.865,0.396 false 1.771,0.229 2.083,0.427 0.313,0.198 10 false *b 0.313,0.229 0.625,0.427 0.313,0.198 10 false *a
*a Multi-information Display
*b Audio Tab


Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

The audio tab illuminates and DTC B150A is not output.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY