Home › Drivetrain › K111 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0060958 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1586  Acceleration Sensor Malfunction  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1586 Acceleration Sensor Malfunction 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The ignition switch is ON.

2.

With the vehicle speed at 30 km/h (18 mph) or more, the difference between the longitudinal acceleration calculated based on the G sensor value and the longitudinal acceleration calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more.

3.

3.0 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

No change detected in the yaw rate and acceleration sensor signal 16 times or more while the vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph).

3.

3.0 seconds

4.

1 trip detection logic


·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)

·

CAN communication system


- DTC stored

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

DTCs are not output

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

DTCs are output

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)
a.

Clear the DTCs.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > Engine and ECT > Clear DTCs
50002 234

b.

Perform a road test where the vehicle is driven at 30 km/h (18 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs using the GTS.

Result:
Proceed to
Only P1586 is output
P1586 and other DTCs are output


HINT:

If any other DTCs besides DTC P1586 are output, perform troubleshooting for those DTCs first.




Only P1586 is output

3.READ VALUE USING GTS (G SENSOR)

P1586 and other DTCs are output

3.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor min.: 0 V
max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Result Proceed to
Data displayed is as specified under Normal Condition A
Data displayed is not as specified under Normal Condition B




A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

4.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
4.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT