Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1401

DTC No. Detection Item DTC Detection Condition Trouble Area
C1405 Open or Short in Front Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C1406 Open or Short in Front Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor LH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

C241007E39
0.396,2.219 1.25,2.625 0.854,0.406 10 false Front Speed Sensor RH 2.302,0.635 2.458,0.802 0.156,0.167 10 false 1 2.302,1.104 2.417,1.292 0.115,0.188 10 false 2 0.344,1.021 1.167,1.427 0.823,0.406 10 false Front Speed Sensor LH 2.292,1.833 2.438,1.99 0.146,0.156 10 false 1 2.313,2.313 2.427,2.479 0.115,0.167 10 false 2 5,3.104 6.521,3.531 1.521,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 5.25,1.146 5.448,1.385 0.198,0.24 10 false 17 5.552,1.979 5.844,2.125 0.292,0.146 10 false FR+ 5.24,0.667 5.469,0.906 0.229,0.24 10 false 18 5.573,2.438 5.865,2.583 0.292,0.146 10 false FR- 5.26,2.354 5.5,2.583 0.24,0.229 10 false 30 5.563,0.781 5.927,0.969 0.365,0.188 10 false FL+ 5.271,1.865 5.521,2.052 0.25,0.188 10 false 31 5.583,1.26 5.875,1.406 0.292,0.146 10 false FL- 0.365,0.781 0.729,0.948 0.365,0.167 10 false A14 0.427,2.031 0.792,2.198 0.365,0.167 10 false A43 5.042,2.906 5.313,3.052 0.271,0.146 10 false A80 1.917,0.771 2.281,0.938 0.365,0.167 10 false FL+ 1.927,1.25 2.177,1.396 0.25,0.146 10 false FL- 1.896,1.958 2.188,2.104 0.292,0.146 10 false FR+ 1.906,2.438 2.198,2.583 0.292,0.146 10 false FR-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1405 and C1406 are not output
DTCs C1405 and/or C1406 are output



DTCs C1405 and C1406 are not output

DTCs C1405 and/or C1406 are output

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A80 skid control ECU (brake actuator assembly) connector and the A14 and/or A43 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A80-31 (FR+) - A43-1 (FR+) Always Below 1 Ω
A80-30 (FR-) - A43-2 (FR-) Always Below 1 Ω
A80-31 (FR+) or A43-1 (FR+) - Body ground Always 10 kΩ or higher
A80-30 (FR-) or A43-2 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A80-18 (FL+) - A14-1 (FL+) Always Below 1 Ω
A80-17 (FL-) - A14-2 (FL-) Always Below 1 Ω
A80-18 (FL+) or A14-1 (FL+) - Body ground Always 10 kΩ or higher
A80-17 (FL-) or A14-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


b.
C271648C01
0.906,0.448 1.292,0.719 0.385,0.271 2.208,0.469 2.625,0.729 0.417,0.26 1.198,1.844 1.135,1.427 false 2.385,1.833 2.51,1.427 false 0,0 0.313,0.156 0.313,0.156 10 false *a 0.99,0.49 1.448,0.688 0.458,0.198 10 false A43 2.26,0.49 2.719,0.688 0.458,0.198 10 false A14 1.135,1.896 1.594,2.094 0.458,0.198 10 false FR+ 2.271,1.906 2.729,2.104 0.458,0.198 10 false FL+ 1.021,0.219 1.333,0.417 0.313,0.198 10 false *A 2.354,0.198 2.667,0.396 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A43-1 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A14-1 (FL+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

NG