Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more while the vehicle is being driven at a speed of 3 km/h (2 mph) or more.
·

STOP fuse

·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Brake actuator assembly (Master cylinder pressure sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1422 is output
DTCs C1422 and C1380 are output
DTCs C1422 and C1425 are output




DTC C1422 is output

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

DTCs C1422 and C1380 are output

DTCs C1422 and C1425 are output

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


e.

In accordance with the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37
f.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.


OK:

The GTS displays ON or OFF according to brake pedal operation.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


e.

In accordance with the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Pressure Master cylinder pressure sensor pressure Min.: 0.00 MPa
Max.: 23.28 MPa
Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Pressure
50003 105 393
OK:

Data List pressure is within standard range.


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1422 is not output
DTC C1422 is output



DTC C1422 is not output

DTC C1422 is output

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C342353C29
1.49,0.104 1.865,0.375 0.375,0.271 2.646,1.813 2.646,1.625 2.646,1.625 2.198,1.323 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.573,0.156 2.031,0.354 0.458,0.198 10 false A80 2.531,1.844 2.906,2.031 0.375,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A80 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-35 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR