Steering angle sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.
When a malfunction occurs in the communication line to the steering angle sensor, U0126 is output.
If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
DTCs may be stored if one of the following occurs:
Steering angle sensor zero point malfunction
Steering angle sensor signal malfunction
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1434 | Steering Angle Sensor Output Malfunction | Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point. | ·
ECU-B NO. 1 fuse ·
ECU-IG NO. 1 fuse ·
Steering angle sensor (Spiral with sensor cable sub-assembly) ·
Skid control ECU (Brake actuator assembly) ·
Wire harness or connector |
Refer to DTC C1432.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1432
Do not remove the steering angle sensor from the spiral with sensor cable sub-assembly.
When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073
When any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be output even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) sensor is normal.
If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral with sensor cable sub-assembly).
| Result | Proceed to |
|---|---|
| No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output | A |
| DTC (relating to CAN communication system) is output (for LHD with Central Gateway ECU) | B |
| DTC (relating to CAN communication system) is output (for RHD with Central Gateway ECU) | C |
| DTC (relating to CAN communication system) is output (for LHD without Central Gateway ECU) | D |
| DTC (relating to CAN communication system) is output (for RHD without Central Gateway ECU) | E |
| Speed sensor or yaw rate and acceleration sensor DTC is output | F |
A
B
C
D
E
F
Turn the ignition switch off.
Remove the steering wheel and the column cover lower.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL
| *a | Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the G12 steering angle sensor (spiral with sensor cable sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G12-5 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G12-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG (w/o Stop and Start System) |
| NG (w/ Stop and Start System) |
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G12-1 (ESS) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG