Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during trailer sway control*, VSC or TRC/TRAC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM

*: w/ Trailer Sway Control


WIRING DIAGRAM

C341477E02
5.49,5.281 7.104,5.75 1.615,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.469,5.073 5.792,5.313 0.323,0.24 10 false A80 6.146,4.021 6.76,4.219 0.615,0.198 10 false GND1 5.802,3.833 6.125,4.073 0.323,0.24 10 false 25 6.167,2.094 6.781,2.292 0.615,0.198 10 false IG1 5.833,1.938 6.156,2.177 0.323,0.24 10 false 12 3.042,3.208 3.656,3.406 0.615,0.198 10 false IG31 3.469,3.042 4.083,3.24 0.615,0.198 10 false 1 1.542,3.781 4.042,4.115 2.5,0.333 10 false Engine Stop and Start ECU*1 1.531,3.563 1.854,3.802 0.323,0.24 10 false G87 3.854,2.24 4.854,2.51 1,0.271 10 false ECU-IG NO. 3 2.073,2.073 3.125,2.375 1.052,0.302 10 false from IG Circuit 0.115,5.333 1.99,5.625 1.875,0.292 10 false Combination Meter Assembly 4.896,3.052 5.219,3.292 0.323,0.24 10 false *1 2.292,5.292 4.792,5.625 2.5,0.333 10 false *1: w/ Stop and Start System 2.354,5.615 4.854,5.948 2.5,0.333 10 false *2: w/o Stop and Start System 4.875,1.917 5.198,2.156 0.323,0.24 10 false *2 0.771,6.344 2.917,6.667 2.146,0.323 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)



DTC is not output

3.INSPECT BATTERY

DTC is output (for LHD with Central Gateway ECU)

DTC is output (for RHD with Central Gateway ECU)

DTC is output (for LHD without Central Gateway ECU)

DTC is output (for RHD without Central Gateway ECU)

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 2WW)




OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

NG (for 2WW)

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C342353C30
1.49,0.104 1.865,0.375 0.375,0.271 2.938,0.313 2.75,0.313 2.75,0.313 2.417,0.854 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.563,0.156 2.021,0.354 0.458,0.198 10 false A80 2.99,0.24 3.271,0.438 0.281,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A80-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C342353C26
1.49,0.104 1.865,0.375 0.375,0.271 0.208,1.646 0.208,1.5 0.208,1.5 0.698,1.229 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.563,0.156 2.021,0.354 0.458,0.198 10 false A80 0.052,1.677 0.667,1.875 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-25 (GND1) - Body ground Always Below 1 Ω



c.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)
a.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slip Indicator Light SLIP indicator light OFF or ON OFF: Indicator light off
ON: Indicator light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Slip Indicator Light
50003 105 304

g.

Check the GTS display condition of the slip indicator light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON