Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:
Gear position is not R.
The brake system is malfunctioning.
The vehicle speed is 25 km/h (15 mph) or more.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check if CAN communication system DTCs are output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output (for LHD with Central Gateway ECU) |
| DTC is output (for RHD with Central Gateway ECU) |
| DTC is output (for LHD without Central Gateway ECU) |
| DTC is output (for RHD without Central Gateway ECU) |
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)
Turn the ignition switch off.
Disconnect the A80 skid control ECU (brake actuator assembly) connector.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A80-27 (HDCS) - Body ground | Downhill assist control switch is pushed | Below 1 Ω |
| A80-27 (HDCS) - Body ground | Downhill assist control switch is not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A80 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Downhill Assist Control Light | Downhill assist control indicator light | Indicator light OFF/ON | Observe combination meter
Vehicle condition: Vehicle stopped |
When performing the ABS Warning Light Active Test, check Downhill assist control indicator light in the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Downhill Assist Control Light | Downhill assist control indicator light | ON or OFF | OFF: Downhill assist control indicator light off
ON: Downhill assist control indicator light on |
w/ Downhill Assist Control:
The item is displayed on the GTS but not used. OFF: Always |
| Active Test Display |
|---|
| Downhill Assist Control Light |
| Data List Display |
|---|
| Downhill Assist Control Light |
| Result | Proceed to |
|---|---|
| Downhill assist control indicator light in the Data List does not change using the Active Test | A |
| Downhill assist control indicator light in the Data List turns ON/OFF using the Active Test | B |
A
B
Turn the ignition switch off.
Perform Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| Indicat. Downhill Assist Control |
Check the combination meter assembly.
The Downhill assist control indicator light turns on or off in accordance with the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Remove the downhill assist control switch.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>REMOVAL
Inspect the downhill assist control switch.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A80-27 (HDCS) - G29-4 | Always | Below 1 Ω |
| A80-27 (HDCS) or G29-4 - Body ground | Always | 10 kΩ or higher |
| G29-1 - Body ground | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG