Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1586  Acceleration Sensor Malfunction  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly). If a malfunction of the yaw rate and acceleration sensor (airbag sensor assembly) is determined based on a malfunction signal from the skid control ECU (brake actuator assembly), the ECM stores this DTC.

HINT:
·

The yaw rate and acceleration sensor (airbag sensor assembly) signal is sent to the skid control ECU (brake actuator assembly) via CAN communication.

·

If CAN communication DTCs are output, perform troubleshooting for those DTCs first.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1586 Acceleration Sensor Malfunction 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

The ignition switch is ON.

2.

At a vehicle speed 30 km/h (19 mph) or more, the difference between longitudinal G calculated based on the yaw rate and acceleration sensor (airbag sensor assembly) (G sensor) value and longitudinal G calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more.

3.

3 seconds or more

4.

1-trip detection logic


DTC Detection Condition 2:
1.

The ignition switch is ON.

2.

The yaw rate and acceleration sensor (airbag sensor assembly) signal does not change 16 times or more while the vehicle speed decreases from 30 km/h (19 mph) to 0 km/h (0 mph).

3.

3 seconds or more

4.

1-trip detection logic


·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)

·

CAN communication system


Does not come on DTC stored

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC U0129 is not output A
DTC U0129 is output B



A

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

B

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Turn the ignition switch to ON.


d.

Clear the DTCs.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Perform a road test where the vehicle is driven at 30 km/h (18 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P1586 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P1586 is output A
DTC P1586 and other DTCs are output B



A

3.READ VALUE USING GTS (G SENSOR)

B

3.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of G sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of G sensor
·

2.31 V to 2.69 V: Vehicle on level ground

·

1.88 V to 2.5 V: Decelerating

·

2.5 V to 3.11 V: Accelerating

·

Set to 1.87 V: G sensor malfunction

·

Set to 1.87 V: Communication malfunction


-
Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

4.REPLACE AIRBAG SENSOR ASSEMBLY

B

4.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT