Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0451  Evaporative Emission Control System Pressure Sensor Range / Performance  P0452  Evaporative Emission Control System Pressure Sensor / Switch Low Input  P0453  Evaporative Emission Control System Pressure Sensor / Switch High Input  


DTC SUMMARY

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0451 Evaporative Emission Control System Pressure Sensor Range / Performance Either of the following conditions is met:
·

Sensor output voltage fluctuates frequently in a certain time period.

·

Sensor output voltage does not vary in a certain time period.


·

Canister pump module

·

Connector/wire harness

(canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


Comes on DTC stored
P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input EVAP pressure sensor less than 42.11 kPa(abs) [315.867 mmHg(abs)] for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


Comes on DTC stored
P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input EVAP pressure sensor higher than 123.761 kPa(abs) [928.331 mmHg(abs)] for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


Comes on DTC stored

DTC No. Monitoring Item Detection Timing Detection Logic
P0451 Canister pressure sensor abnormal voltage fluctuation
·

EVAP monitoring (engine switch off)

·

Engine running


2 trip
Canister pressure sensor constant voltage
·

EVAP monitoring (engine switch off)


2 trip
P0452 Canister pressure sensor low input
·

Engine switch on (IG)

·

EVAP monitoring (engine switch off)


1 trip
P0453 Canister pressure sensor high input
·

Engine switch on (IG)

·

EVAP monitoring (engine switch off)


1 trip

HINT:

The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>EVAP System

MONITOR DESCRIPTION

A115543E70
4.552,3.302 4.969,3 true 4.521,1.427 4.958,1.052 true 0.094,0.083 3.083,0.292 2.99,0.208 10 Canister Pressure Sensor Specification: 5.115,3.344 5.792,3.604 0.677,0.26 10 Pressure 1.302,1.021 2.365,1.281 1.063,0.26 10 Output Voltage 1.698,1.448 2.281,1.708 0.583,0.26 10 4.900 V 1.698,1.917 2.281,2.177 0.583,0.26 10 4.423 V 1.698,2.615 2.281,2.875 0.583,0.26 10 1.425 V 1.698,3.094 2.281,3.354 0.583,0.26 10 0.450 V 5.01,2.917 6.135,3.177 1.125,0.26 10 Malfunction Area 5,0.958 6.125,1.219 1.125,0.26 10 Malfunction Area 3.844,2.292 4.813,2.552 0.969,0.26 10 Usable Range 1.833,4.25 6.656,4.479 4.823,0.229 10 Standard atmospheric pressure is 101.3 kPa(abs) [760 mmHg(abs)] 1.833,4.031 2.292,4.292 0.458,0.26 10 HINT: 3.583,3.458 3.969,3.844 0.385,0.385 10 115 (862) 2.896,3.458 3.281,3.844 0.385,0.385 10 60 (450) 4.344,3.448 5.333,3.906 0.99,0.458 10 kPa(abs) [mmHg(abs)]

1.

DTC P0451: Canister pressure sensor abnormal voltage fluctuation or being constant

If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC.

Alternatively, if the sensor voltage output does not change for 2 minutes, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC.

(Both the malfunctions are detected by 2 trip detection logic).

2.

DTC P0452: Canister pressure sensor voltage low

If the canister pressure sensor voltage output (pressure) is less than 0.45 V: 42.11 kPa(abs) [315.867 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

3.

DTC P0453: Canister pressure sensor voltage high

If the canister pressure sensor voltage output (pressure) is higher than 4.9 V: 123.761 kPa(abs) [928.331 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).


MONITOR STRATEGY

Required Sensors/Components Canister pump module
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).



1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

4.

Check that the intake air temperature is between 4.4 and 35°C (40 and 95°F).

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the engine switch off and wait for at least 30 seconds.

7.

Turn the engine switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

9.

After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0451, P0452 or P0453.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A290314E01
5.417,0.563 5.917,0.729 0.5,0.167 10 false MPMP 5.417,1.625 5.833,1.792 0.417,0.167 10 false VCPP 5.417,2.083 5.917,2.25 0.5,0.167 10 false PPMP 5.417,2.552 5.917,2.719 0.5,0.167 10 false EPPM 5.417,3.219 5.917,3.385 0.5,0.167 10 false VPMP 5.417,6.229 5.917,6.396 0.5,0.167 10 false MREL 5.417,4.573 5.833,4.74 0.417,0.167 10 false PRG 5.042,0.667 5.438,0.844 0.396,0.177 10 false A62 5.083,0.479 5.333,0.646 0.25,0.167 10 false 19 1.667,1 3.083,1.167 1.417,0.167 10 false Leak Detection Pump 3.333,0.563 3.5,0.729 0.167,0.167 10 false 3 1.177,0.563 1.344,0.729 0.167,0.167 10 false 4 1.188,3.219 1.354,3.385 0.167,0.167 10 false 5 3.333,3.219 3.5,3.385 0.167,0.167 10 false 1 3.333,2.552 3.5,2.719 0.167,0.167 10 false 8 3.333,2.083 3.5,2.25 0.167,0.167 10 false 7 3.333,1.625 3.5,1.792 0.167,0.167 10 false 6 2.802,0.563 3.292,0.729 0.49,0.167 10 false MTRB 1.417,0.563 1.917,0.729 0.5,0.167 10 false MGND 1.583,1.75 2.25,2.333 0.667,0.583 10 false Canister Pressure Sensor 2,3.5 2.75,3.667 0.75,0.167 10 false Vent Valve 1.417,3.219 1.833,3.385 0.417,0.167 10 false VLVB 2.792,2.76 3.292,2.927 0.5,0.167 10 false SGND 2.802,2.073 3.302,2.24 0.5,0.167 10 false VOUT 2.896,1.625 3.313,1.792 0.417,0.167 10 false VCC 2.792,3.219 3.292,3.385 0.5,0.167 10 false VGND 1.583,4.083 3.083,4.25 1.5,0.167 10 false Canister Pump Module 1.583,3.917 1.833,4.167 0.25,0.25 10 false V3 3.75,4.583 3.917,4.75 0.167,0.167 10 false 1 4.542,4.583 4.708,4.75 0.167,0.167 10 false 2 3.833,5.167 4.583,5.417 0.75,0.25 10 false Purge VSV 3.833,5 4.083,5.167 0.25,0.167 10 false B2 2.125,4.833 2.792,5 0.667,0.167 10 false EFI NO. 1 3.167,6.667 4.25,6.833 1.083,0.167 10 false EFI-MAIN NO. 1 1.333,6.833 1.917,7.083 0.583,0.25 10 false Battery 3.219,5.865 3.385,6.031 0.167,0.167 10 false 5 4,5.865 4.167,6.031 0.167,0.167 10 false 3 4,6.229 4.167,6.396 0.167,0.167 10 false 1 3.219,6.229 3.385,6.396 0.167,0.167 10 false 2 5.042,1.729 5.375,1.896 0.333,0.167 10 false A62 5.042,2.188 5.375,2.354 0.333,0.167 10 false A62 5.042,2.646 5.375,2.813 0.333,0.167 10 false A62 5.042,3.323 5.375,3.49 0.333,0.167 10 false A62 5.052,4.677 5.385,4.844 0.333,0.167 10 false B77 5.042,6.333 5.375,6.5 0.333,0.167 10 false A62 5.083,1.542 5.333,1.708 0.25,0.167 10 false 34 5.083,2 5.333,2.167 0.25,0.167 10 false 49 5.083,2.458 5.333,2.625 0.25,0.167 10 false 48 5.135,3.135 5.302,3.302 0.167,0.167 10 false 7 5.083,6.146 5.333,6.313 0.25,0.167 10 false 46 5.083,4.49 5.333,4.656 0.25,0.167 10 false 68 1.25,6.135 2.333,6.302 1.083,0.167 10 false EFI-MAIN NO. 1 0.333,4.229 1,4.396 0.667,0.167 10 false EFI NO. 2 0.396,6.365 1.063,6.531 0.667,0.167 10 false FL MAIN 5.792,7.031 6.135,7.208 0.344,0.177 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel tank cap.

·

The GTS is required to conduct the following diagnostic troubleshooting procedure.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) (do not start the engine).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Evaporative / Vapor Pressure Pump.

Powertrain > Engine and ECT > Data List
Tester Display
Vapor Pressure Pump
50003 234 344

g.

Read the EVAP (Evaporative Emission) pressure displayed on the GTS.

Result:
Display (DTC Output) Test Result Suspected Trouble Area Proceed to
P0451 - Canister pressure sensor C
P0452 Less than 42.11 kPa(abs) [315.867 mmHg(abs)]
·

Wire harness/connector (ECM - canister pressure sensor)

·

Canister pressure sensor

·

Short in ECM circuit


A
P0453 Higher than 123.761 kPa(abs) [928.331 mmHg(abs)]
·

Wire harness/connector (ECM - canister pressure sensor)

·

Canister pressure sensor

·

Open in ECM circuit


B




A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

8.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A62-49 (PPMP) - Body ground Always Below 10 Ω
·

Wire harness/connector (ECM - canister pressure sensor)

·

Short in canister pressure sensor circuit


A
10 kΩ or higher
·

Wire harness/connector (ECM - canister pressure sensor)

·

Short in ECM circuit


B




A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A62-49 (PPMP) - Body ground Always 10 kΩ or higher Short in canister pressure sensor circuit A
Below 10 Ω Short in wire harness/connector (ECM - canister pressure sensor) B




A

4.REPLACE CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY (CANISTER PUMP MODULE)

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
4.REPLACE CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY (CANISTER PUMP MODULE)
a.

Replace the charcoal canister leak detection pump sub-assembly.

Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>CANISTER(w/ Canister Pump Module)>REMOVAL

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.



A290281C01
2.563,1.813 2.01,2.583 false 2.177,2.844 2.99,1.833 false 3.625,3.323 3.25,3.813 false 4.74,2.313 5.323,1.823 false 6.74,4.323 6.188,3.667 false 6.083,4.323 6.115,3.76 false 5.552,4.323 5.99,3.615 false 1,2.01 1.458,2.604 false 6.688,4.344 7,4.542 0.313,0.198 10 *3 3.042,1.75 3.354,1.948 0.313,0.198 10 *1 3.156,3.833 3.469,4.031 0.313,0.198 10 *2 5.365,1.729 5.677,1.927 0.313,0.198 10 *4 2.604,1.729 2.917,1.927 0.313,0.198 10 *5 0.802,1.927 1.115,2.125 0.313,0.198 10 *6 5.469,4.354 5.781,4.552 0.313,0.198 10 *7 3.885,1.115 4.198,1.313 0.313,0.198 10 *a 2.125,4.135 2.438,4.333 0.313,0.198 10 *a 6.01,4.344 6.323,4.542 0.313,0.198 10 *8
*1 Fuel Tank Vent Hose *2 Vent Hose
*3 Air Inlet Port *4 Fuel Tank
*5 Canister Pump Module *6 Canister Assembly
*7 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) *8 Fuel Tank Cap Assembly
*a Inspection Area
(check for disconnection and/or cracks)
- -



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
5.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Perform the Evaporative System Check using the GTS, referring to the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

j.

Input the DTC: P0452 or P0453.


k.

Check the DTC judgment result.

Result:
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
HINT:

If the exhaust pipe has been removed, go to the next step before reinstalling it.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
8.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.
A290284C01
0.354,2.583 0.667,2.833 0.313,0.25 2,2.75 2.583,2.417 false 2.25,3.167 1.833,2.75 false 1.583,2.75 1.083,3.167 false 0.083,1.917 0.333,2.073 0.25,0.156 10 false *a 0.427,2.635 0.635,2.844 0.208,0.208 10 false V3 2.333,3.083 2.75,3.25 0.417,0.167 10 false VOUT 0.708,3.083 1.083,3.25 0.375,0.167 10 false VCC 2.667,2.333 3.083,2.5 0.417,0.167 10 false SGND
*a Front view of wire harness connector
(to Canister Pump Module)


Disconnect the canister pump module connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V3-8 (SGND) - Body ground Always 100 Ω or less



c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V3-6 (VCC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
V3-7 (VOUT) - Body ground Engine switch on (IG) 4.5 to 5.5 V


Result:
Test Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and/or resistance outside standard ranges Open in wire harness/connector (ECM - canister pressure sensor) B




A

4.REPLACE CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY (CANISTER PUMP MODULE)

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)