Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Television Camera ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Television Camera ECU Communication Stop Mode Either condition is met:
·

"Parking Assist Monitor System" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Television Camera ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of television camera assembly

·

Television camera assembly CAN branch wire or connector

·

Television camera assembly



WIRING DIAGRAM

C343191E04
5.26,3.792 7.073,4.125 1.813,0.333 10 false Television Camera Assembly 5.26,3.615 6.021,3.979 0.76,0.365 10 false c2 5.677,2.677 6.302,2.99 0.625,0.313 10 false CB+ 5.667,3.188 6.292,3.5 0.625,0.313 10 false CGND 5.458,3.104 6.083,3.417 0.625,0.313 10 false 5 5.469,2.594 6.094,2.906 0.625,0.313 10 false 6 5.438,1.208 6.063,1.521 0.625,0.313 10 false 1 5.438,0.677 6.063,0.99 0.625,0.313 10 false 4 5.667,0.771 6.292,1.083 0.625,0.313 10 false CANH 5.688,1.271 6.313,1.583 0.625,0.313 10 false CANL 1.104,2.667 1.729,2.979 0.625,0.313 10 false CA+ 0.969,3.229 1.594,3.542 0.625,0.313 10 false CGND 1.521,3.115 2.146,3.427 0.625,0.313 10 false 23 1.521,2.604 2.146,2.917 0.625,0.313 10 false 11 0.333,3.604 1.844,3.917 1.51,0.313 10 false G159 0.344,3.792 3,3.969 2.656,0.177 10 false Radio and Display Receiver Assembly 0.292,1.677 0.917,1.99 0.625,0.313 10 false N36 0.292,1.854 2.729,2.167 2.438,0.313 10 false No. 10 CAN Junction Connector 1.531,1.208 2.156,1.521 0.625,0.313 10 false 15 1.51,0.667 2.135,0.979 0.625,0.313 10 false 5 2.083,3.396 4.521,3.708 2.438,0.313 10 false * 0.385,4.385 2.823,4.698 2.438,0.313 10 false *: Shield 2.594,3.396 5.031,3.708 2.438,0.313 10 false * 3.115,3.396 5.552,3.708 2.438,0.313 10 false * 3.615,3.396 6.052,3.708 2.438,0.313 10 false * 4.104,3.396 6.542,3.708 2.438,0.313 10 false * 4.625,3.385 7.063,3.698 2.438,0.313 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE)
a.
C294680C44
1.563,0.219 2,0.469 0.438,0.25 0.969,1.938 1.135,1.938 1.135,1.938 1.51,1.448 true 0.885,0.552 1.052,0.552 1.052,0.552 1.5,1.125 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.698,0.24 2.229,0.552 0.531,0.313 10 false c2 0.542,1.833 1.156,2.031 0.615,0.198 10 false CANH 0.5,0.458 1.115,0.656 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Television Camera Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c2-4 (CANH) - c2-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - BATTERY AND BODY GROUND)
a.
C294680C45
1.573,0.229 2.021,0.479 0.448,0.25 1.385,1.958 1.552,1.958 1.552,1.958 1.948,1.458 true 0.813,0.969 0.979,0.969 0.979,0.969 1.719,1.323 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.698,0.26 2.156,0.458 0.458,0.198 10 false c2 1.052,1.865 1.667,2.063 0.615,0.198 10 false CB+ 0.365,0.865 0.979,1.063 0.615,0.198 10 false CGND
*a Front view of wire harness connector
(to Television Camera Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
c2-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c2-5 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G159 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c2-6 (CB+) - G159-11 (CA+) Always Below 1 Ω
c2-5 (CGND) - G159-23 (CGND) Always Below 1 Ω
c2-6 (CB+) or G159-11 (CA+) - Body ground Always 10 kΩ or higher
c2-5 (CGND) or G159-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR