These DTCs indicate malfunctions relating to the primary circuit.
If DTC P0351 is output, check the ignition coil assembly (No. 1 cylinder) circuit.
If DTC P0352 is output, check the ignition coil assembly (No. 2 cylinder) circuit.
If DTC P0353 is output, check the ignition coil assembly (No. 3 cylinder) circuit.
If DTC P0354 is output, check the ignition coil assembly (No. 4 cylinder) circuit.
A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0351 | Ignition Coil "A" Primary / Secondary Circuit | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM ·
No. 1 ignition coil assembly ·
ECM |
Comes on | DTC stored |
| P0352 | Ignition Coil "B" Primary / Secondary Circuit | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM ·
No. 2 ignition coil assembly ·
ECM |
Comes on | DTC stored |
| P0353 | Ignition Coil "C" Primary / Secondary Circuit | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM ·
No. 3 ignition coil assembly ·
ECM |
Comes on | DTC stored |
| P0354 | Ignition Coil "D" Primary / Secondary Circuit | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM ·
No. 4 ignition coil assembly ·
ECM |
Comes on | DTC stored |
Reference: Inspection using an oscilloscope.
While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
| ECM Terminal Name | IGT: Between IGT (1 to 4) and E1
IGF: Between IGF1 and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
If the ECM does not receive any IGF1 signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
| Required Sensors/Components (Main) | Igniter |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Start the engine and run it at idle for 10 seconds or more.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B100-4 (GND) - Body ground | Always | Below 1 Ω |
| B99-4 (GND) - Body ground | Always | Below 1 Ω |
| B98-4 (GND) - Body ground | Always | Below 1 Ω |
| B97-4 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
Disconnect the ignition coil assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B100-1 (+B) - B100-4 (GND) | Ignition switch ON | 11 to 14 V |
| B99-1 (+B) - B99-4 (GND) | Ignition switch ON | 11 to 14 V |
| B98-1 (+B) - B98-4 (GND) | Ignition switch ON | 11 to 14 V |
| B97-1 (+B) - B97-4 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B100-2 (IGF) - B77-51 (IGF1) | Always | Below 1 Ω |
| B99-2 (IGF) - B77-51 (IGF1) | Always | Below 1 Ω |
| B98-2 (IGF) - B77-51 (IGF1) | Always | Below 1 Ω |
| B97-2 (IGF) - B77-51 (IGF1) | Always | Below 1 Ω |
| B100-3 (IGT1) - B77-57 (IGT1) | Always | Below 1 Ω |
| B99-3 (IGT2) - B77-56 (IGT2) | Always | Below 1 Ω |
| B98-3 (IGT3) - B77-55 (IGT3) | Always | Below 1 Ω |
| B97-3 (IGT4) - B77-54 (IGT4) | Always | Below 1 Ω |
| B100-3 (IGT1) or B77-57 (IGT1) - Body ground | Always | 10 kΩ or higher |
| B99-3 (IGT2) or B77-56 (IGT2) - Body ground | Always | 10 kΩ or higher |
| B98-3 (IGT3) or B77-55 (IGT3) - Body ground | Always | 10 kΩ or higher |
| B97-3 (IGT4) or B77-54 (IGT4) - Body ground | Always | 10 kΩ or higher |
| B100-2 (IGF), B99-2 (IGF), B98-2 (IGF), B97-2 (IGF) or B77-51 (IGF1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR
Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).
Do not change the location of the connectors.
Perform a simulation test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Same DTC output | A |
| Different ignition coil DTC output | B |
Perform "Inspection After Repair" after replacing the ignition coil assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
A
B
Disconnect the ignition coil assembly connectors.
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B100-1 (+B) - IG2 relay terminal 5 | Always | Below 1 Ω |
| B99-1 (+B) - IG2 relay terminal 5 | Always | Below 1 Ω |
| B98-1 (+B) - IG2 relay terminal 5 | Always | Below 1 Ω |
| B97-1 (+B) - IG2 relay terminal 5 | Always | Below 1 Ω |
| B100-1 (+B), B99-1 (+B), B98-1 (+B), B97-1 (+B) or IG2 relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG