Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0336  Crankshaft Position Sensor "A" Circuit Range / Performance  


DESCRIPTION

The crankshaft position sensor monitors the stop position and performs start control from the position of the stopped crankshaft. Moreover, the crankshaft position sensor contains a function which detects reverse rotation to correctly detect the stop position when the engine rotates reversely.

When a malfunction occurs in the reverse rotation detection function, stop and start system is disabled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0336 Crankshaft Position Sensor "A" Circuit Range / Performance When one of the following conditions is met (1 trip detection logic):
·

An engine reverse signal is detected for 4 seconds while the engine is cranking or running normally at 900 rpm or higher.

·

The pulse width of the crankshaft position sensor is detected to have exceeded the threshold for 4 seconds while the engine is running at 900 rpm or higher.

·

The input signal voltage of the crankshaft position sensor continues at 4.7 V for 4 seconds while the engine is running.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When one of the following malfunctions is detected, P0336 is output.

1.

An engine reverse signal is detected for 4 seconds while the engine is cranking or runnning normally at 900 rpm or higher.

2.

The case the pulse width of the crankshaft position sensor is detected to have exceededthe threshold for 4 seconds while the engine is running normally at 900 rpm or higher.

3.

The input signal voltage of the crankshaft position sensor continues at 4.7 V for 4 seconds while the engine runnning.


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0336.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0336)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0336 and P0338 are output A
DTC P0336 is output B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)

B

6.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
a.
A209301C70
0.042,0.542 0.448,0.844 0.406,0.302 0.042,0.958 0.448,1.292 0.406,0.333 1.052,1.792 1.406,1.271 true 0.823,1.823 1.26,2.083 0.438,0.26 10 false VC 0.094,0.146 0.531,0.406 0.438,0.26 10 false *a 0.125,1.021 0.563,1.281 0.438,0.26 10 false B88 0.083,0.583 0.698,0.781 0.615,0.198 10 false B106 0.49,0.573 1.104,0.771 0.615,0.198 10 false *A 0.5,1.031 0.813,1.229 0.313,0.198 10 false *B
*A for Manual Transaxle Models, w/ Stop and Start System
*B except *A
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Manual Transaxle Models, w/ Stop and Start System
Tester Connection Condition Specified Condition
B106-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V

except Manual Transaxle Models, w/ Stop and Start System
Tester Connection Condition Specified Condition
B88-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle Models, w/ Stop and Start System
Tester Connection Condition Specified Condition
B106-3 (NE+) - B93-114 (NE+) Always Below 1 Ω
B106-2 (NE-) - B93-113 (NE-) Always Below 1 Ω
B106-3 (NE+) or B93-114 (NE+) - Body ground and other terminals Always 10 kΩ or higher
B106-2 (NE-) or B93-113 (NE-) - Body ground and other terminals Always 10 kΩ or higher

except Manual Transaxle Models, w/ Stop and Start System
Tester Connection Condition Specified Condition
B88-3 (NE+) - B93-114 (NE+) Always Below 1 Ω
B88-2 (NE-) - B93-113 (NE-) Always Below 1 Ω
B88-3 (NE+) or B93-114 (NE+) - Body ground and other terminals Always 10 kΩ or higher
B88-2 (NE-) or B93-113 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
B319222C07
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the No. 1 crankshaft position sensor plate.

OK:

No. 1 crankshaft position sensor plate does not have any cranks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTCs are not output A
DTC P0336 is output B



A

END

B

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle Models, w/ Stop and Start System
Tester Connection Condition Specified Condition
B106-1 (VC) - B93-81 (VCNE) Always Below 1 Ω
B106-1 (VC) or B93-81 (VCNE) - Body ground and other terminals Always 10 kΩ or higher

except Manual Transaxle Models, w/ Stop and Start System
Tester Connection Condition Specified Condition
B88-1 (VC) - B93-81 (VCNE) Always Below 1 Ω
B88-1 (VC) or B93-81 (VCNE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR