Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221949 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Detection Item Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of 4WD ECU assembly

·

4WD ECU assembly CAN branch wire or connector

·

4WD ECU assembly



WIRING DIAGRAM

C280380E03
0.229,1.604 1.104,1.958 0.875,0.354 10 false G189 0.229,1.76 2.302,2.104 2.073,0.344 10 false No. 7 CAN Junction Connector 1.698,1.135 2.24,1.531 0.542,0.396 10 false 16 1.698,0.563 3.719,0.917 2.021,0.354 10 false 6 5.448,1.135 6.281,1.604 0.833,0.469 10 false 5 5.448,0.563 6.281,1.031 0.833,0.469 10 false 6 5.656,0.667 6.49,1.135 0.833,0.469 10 false CANH 5.656,1.25 6.49,1.719 0.833,0.469 10 false CANL 5.677,2.417 6.51,2.885 0.833,0.469 10 false IG1 5.438,2.323 6.271,2.792 0.833,0.469 10 false 3 5.427,3.135 6.26,3.604 0.833,0.469 10 false 4 5.656,3.271 6.49,3.74 0.833,0.469 10 false GND 4.146,2.271 5.021,2.729 0.875,0.458 10 false ECU-IG NO.1 2.198,2.438 3.49,2.875 1.292,0.438 10 false from IG1 NO.1 Relay 5.458,3.896 6.75,4.333 1.292,0.438 10 false G86 5.469,4.063 6.979,4.5 1.51,0.438 10 false 4WD ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicles for 4.5 seconds or more at a speed 60 km/h (37 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (4WD ECU ASSEMBLY CAN BRANCH WIRE)
a.
C251077C03
0.333,0.958 0.75,1.25 0.417,0.292 2.583,1.5 2.417,1.5 2.417,1.5 2.24,1.24 true 2.51,1.75 2.344,1.75 2.344,1.75 2.177,1.25 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.396,1.021 0.854,1.219 0.458,0.198 10 G86 2.625,1.406 3.083,1.604 0.458,0.198 10 CANL 2.563,1.656 3.021,1.854 0.458,0.198 10 CANH
*a Rear view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4WD ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C251077C04
2.563,0.948 2.979,1.24 0.417,0.292 1.344,1.052 1.083,0.583 1.083,0.583 0.833,0.583 true 0.75,0.833 0.917,0.833 0.917,0.833 1.219,1.063 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.625,1 3.083,1.198 0.458,0.198 10 G86 0.594,0.521 1.052,0.719 0.458,0.198 10 IG1 0.417,0.771 0.875,0.969 0.458,0.198 10 GND
*a Rear view of wire harness connector
(to 4WD ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G86-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR