Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for RH Side) › from 2015.10
RM3090E _58 Vehicle Interior _008433 SEAT _0049738 REAR SEAT ASSEMBLY(for RH Side) A

SEAT  REAR SEAT ASSEMBLY(for RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.


PROCEDURE

Hide 87510P 1.INSTALL REAR SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)

Hide 71077S 2.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.
B340935C01
1.729,1.542 1.979,0.448 1.979,0.448 2.24,0.448 false 2.302,0.365 2.615,0.521 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seatback cover in place.


b.

Using hog ring pliers, install the separate type rear seatback cover to the rear seat cushion pad RH with 11 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.
B340940C01
1.833,1.5 2.042,0.354 2.042,0.354 2.365,0.354 false 2.438,0.271 2.75,0.427 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 2 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 3.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

a.

Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.


b.
B340616

Attach the 4 claws to install the 2 rear seat headrest supports.


c.
B429046

Attach the 6 hooks.


Hide 71881 4.INSTALL REAR SEATBACK BOARD RH

a.
B429045

Move the rear seatback board RH in the direction of the arrow to attach the guide.


b.

Attach the 5 claws to install the rear seatback board assembly RH.


c.
B429043

Close the 2 fasteners.


d.
B429041C01
1.615,3.885 1.885,3.031 1.885,3.031 2.052,3.031 false 2.083,2.938 2.396,3.094 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 4 new hog rings and attach the 2 pieces of fastener.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 5.INSTALL NO. 1 SEATBACK ASSEMBLY RH

a.
B340613

Install the No. 1 seatback assembly RH to the rear seat reclining adjuster assembly RH with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73380D 6.INSTALL REAR SEAT INNER BELT ASSEMBLY RH

Hide 73330C 7.INSTALL REAR SEAT CENTER LAP TYPE BELT ASSEMBLY RH

Hide 72380 8.INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY

a.
B434010C01
0.5,1.698 1.104,1.781 true 0.344,1.021 1.208,0.406 true 2.083,1.031 3.073,1.208 true 1.531,1.792 1.375,2.49 true 1.385,2.49 1.833,1.865 true 0.698,1.229 1.49,0.917 true 3.198,2.156 2.927,1.615 true 0.313,1.625 0.51,1.802 0.198,0.177 10 false *1 1.896,0.938 2.083,1.104 0.188,0.167 10 true *3 1.542,0.844 1.75,1.021 0.208,0.177 10 false *4 1.281,2.521 1.479,2.677 0.198,0.156 10 true *2 3.146,2.198 3.344,2.385 0.198,0.188 10 false *4 3.156,1.531 3.354,1.729 0.198,0.198 10 false (1) 0.323,1.281 0.521,1.479 0.198,0.198 10 true (1) 0.104,0.552 0.302,0.75 0.198,0.198 10 true (2) 2.74,0.917 2.938,1.115 0.198,0.198 10 true (2) 1.26,0.292 1.448,0.458 0.188,0.167 10 true *3
*1 Cable Clamp A
*2 Clamp
*3 Cable End
*4 Cable Clamp B


Pass the No. 2 seat adjuster control cable assembly through the hole of the rear seat reclining adjuster assembly RH.


b.

Attach the cable clamp (A).


c.

Install the 2 clamps.


d.

Connect the 2 cable ends in the order shown in the illustration.


e.

Attach the 2 cable clamps (B).


Hide 71828B 9.INSTALL REAR SEAT REAR CUSHION MOULDING RH

a.
B340609C01
3.031,1.792 2.698,1.427 true 2.698,1.885 2.219,1.49 true 2.969,0.854 2.406,0.406 true 3.063,1.792 3.24,1.958 0.177,0.167 10 false *1 3.021,0.875 3.333,1.031 0.313,0.156 10 false *2 2.74,1.885 2.917,2.052 0.177,0.167 10 false *1
*1 Clamp
*2 Guide


Attach the guide and claw to install the rear seat rear cushion moulding RH.


b.

w/ Seat Belt Warning System:

Attach the 2 clamps to connect the wire harness.


Hide 71825B 10.INSTALL REAR SEAT CUSHION MOULDING RH

a.
B340606

Attach the 2 guides and claw to install the rear seat cushion moulding RH.


Hide 71303C 11.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH (w/ Child Restraint System Guide)

a.
B429018

Attach the 2 claws to install the rear seatback hinge sub-assembly RH.


Hide 71304C 12.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH (w/ Child Restraint System Guide)

a.
B429016

Attach the 2 claws to install the rear seatback hinge sub-assembly LH.


Hide 72995A 13.INSTALL REAR SEAT COVER

a.
B340607

w/o Child Restraint System Guide:

i.

Attach the claw to install the rear seat cover.


ii.

Install the clip and screw.



b.
B429014

w/ Child Restraint System Guide:

i.

Attach the 4 claws to install the rear seat cover.


ii.

Install the screw.



Hide 72996 14.INSTALL REAR SEATBACK COVER RH

a.
B340608

w/o Child Restraint System Guide:

i.

Attach the claw to install the rear seatback cover RH.


ii.

Install the clip and screw.



b.
B429012

w/ Child Restraint System Guide:

i.

Attach the 4 claws to install the rear seatback cover RH.


ii.

Install the screw.



Hide 71015A 15.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.
B429039

Install the rear seat cushion frame sub-assembly RH with the 4 bushes and 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 2 seat adjuster control cable assembly to the rear seat cushion frame sub-assembly RH with the 3 clamps.

B434011C01
5.51,0.667 6.219,0.625 true 4.198,0.365 4.792,0.667 true 5.427,1.521 6.271,1.313 true 0.906,0.938 1.938,0.604 true 3.063,1.375 2.188,1.25 true 6.281,0.542 6.594,0.698 0.313,0.156 10 false *1 0.719,0.875 0.927,1.042 0.208,0.167 10 false *2 4,0.26 4.219,0.406 0.219,0.146 10 false *1 6.313,1.24 6.625,1.396 0.313,0.156 10 false *1 3.125,1.281 3.438,1.438 0.313,0.156 10 false *3 2.438,0.646 2.667,0.844 0.229,0.198 10 false (1) 1.448,0.406 1.677,0.604 0.229,0.198 10 false (2)
*1 Clamp *2 Cable End
*3 Cable Clamp - -



c.

Connect the cable end in the order shown in the illustration.


d.

Attach the cable clamp.


Hide 72996A 16.INSTALL REAR SEATBACK COVER

a.
B434012

Attach the 2 claws to install the rear seatback cover.


Hide 87510Q 17.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)

Hide 71075S 18.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.

Set the separate type rear seat cushion cover in place.


b.
B340936C01
1.708,1.646 1.969,0.531 1.969,0.531 2.281,0.531 false 2.323,0.448 2.635,0.604 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad RH with 13 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.
B340945C01
1.844,1.49 2.063,0.375 2.063,0.375 2.406,0.375 false 2.479,0.24 2.792,0.396 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install a new hog ring.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




Hide 19.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.
B429037C01
1.854,3.823 1.979,3.146 1.979,3.146 2.219,3.146 false 2.281,3.063 2.594,3.219 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 3 new hog rings.


b.
B429035

Install the separate type seat cushion cover with pad to the rear seat cushion frame sub-assembly RH with the 18 hooks.


c.
B429034

w/ Seat Heater System:

i.

Connect the connector.


ii.

Attach the 4 clamps to connect the wire harness.



Hide 71692E 20.INSTALL REAR SEAT NO. 2 CUSHION HINGE COVER

B340625

a.

Attach the guide and 4 claws to install the rear seat No. 2 cushion hinge cover.


Hide 71691E 21.INSTALL REAR SEAT NO. 1 CUSHION HINGE COVER

a.
B340597

Attach the guide and 4 claws to install the rear seat No. 1 cushion hinge cover.


Hide 72525A 22.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.
B340934

Install the reclining adjuster release handle RH with the 3 screws.


Hide 71845D 23.INSTALL REAR SEAT COVER CAP RH

a.
B434013

Attach the 3 claws to install the rear seat cover cap RH.


Hide 71940A 24.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the rear seat headrest assembly.