Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING › from 2015.10
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050282 WHEEL OPENING MOULDING A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 52119A 1.REMOVE FRONT BUMPER COVER

Hide 52159 2.REMOVE REAR BUMPER COVER

Hide 76622D 3.REMOVE FRONT FENDER MUDGUARD LH (w/ Mudguard)

a.
B338494

Remove the clip.


b.

Remove the 3 screws and front fender mudguard LH.


Hide 75612D 4.REMOVE FRONT FENDER FRONT OUTSIDE MOULDING LH

HINT:

When removing the front fender front outside moulding LH, heat the vehicle body and front fender front outside moulding LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Fender Front Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or front fender front outside moulding LH excessively.


a.
B432920C01
2.177,0.417 2.458,0.177 2.458,0.177 2.729,0.177 true 2.333,2.021 2.167,1.719 2.167,1.719 1.865,1.719 true 1.104,1.188 1.104,0.938 true 2.771,0.094 3.083,0.292 0.313,0.198 10 true *a 1.01,1.188 1.323,1.385 0.313,0.198 10 true *b 1.646,1.625 1.844,1.854 0.198,0.229 10 true *c
*a Double-sided Tape
*b Clip A
*c Clip B
V100155

Protective Tape


Remove the clip labeled A and clip labeled B.


b.

Remove the 5 grommets.


c.

Put protective tape around the front fender front outside moulding LH.


d.

Using a moulding remover, detach the 8 clips.


e.

Detach the double-sided tape to remove the front fender front outside moulding LH.


Hide 65632D 5.REMOVE REAR WHEEL HOUSE FRONT PLATE LH

B338495

a.

Remove the screw.


b.

Detach the clip and rear wheel house front plate LH.


Hide 75656C 6.REMOVE CENTER QUARTER OUTSIDE MOULDING LH

HINT:

When removing the center quarter outside moulding LH, heat the vehicle body and center quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Center Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or center quarter outside moulding LH excessively.


a.
B422088C01
2.573,0.438 2.74,0.167 2.74,0.167 2.99,0.167 true 3.031,0.094 3.271,0.344 0.24,0.25 10 true *a
*a Double-sided Tape
V100155

Protective Tape


Remove the 2 clips and grommet.


b.

Put protective tape around the center quarter outside moulding LH.


c.

Using a moulding remover, detach the 9 clips.


d.

Detach the double-sided tape to remove the center quarter outside moulding LH.