Home › Engine / Hybrid System › 2AR-FE COOLING › RADIATOR › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _008400 2AR-FE COOLING _0046906 RADIATOR A

2AR-FE COOLING  RADIATOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 16711 1.INSTALL FAN SHROUD

a.

Install the fan shroud with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 88460 2.INSTALL COOLER CONDENSER ASSEMBLY

a.

Attach the 2 guides to install the condenser assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER(for 3ZR-FE, 3ZR-FAE, 2AR-FE)>INSTALLATION


Hide 16712 3.INSTALL NO. 2 FAN SHROUD

a.

Attach the 2 claws to install the No. 2 fan shroud.


b.

Install the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 16535 4.INSTALL LOWER RADIATOR SUPPORT

a.

Install the 2 lower radiator supports to the fan shroud.


Hide 16268L 5.INSTALL WATER BY-PASS PIPE

a.

Install the water by-pass pipe to the radiator, and slide the hose clamp to secure it.


b.

Attach the 2 clamps to install the water by-pass pipe.


Hide 16572D 6.INSTALL NO. 2 RADIATOR HOSE

a.

Install the No. 2 radiator hose to the radiator assembly, and slide the hose clamp to secure it.

HINT:

Install the hose clamp with the claw facing downward.



Hide 16057 7.INSTALL RADIATOR HOSE SUB-ASSEMBLY

a.

Install the radiator hose sub-assembly to the radiator assembly and water by-pass pipe, and slide the 2 hose clamps to secure it.


Hide 16400 8.INSTALL RADIATOR ASSEMBLY

a.

Install the radiator assembly together with the fan shroud.

NOTICE:

Make sure that both lower radiator supports are attached to the fan shroud.



Hide 16264D 9.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the radiator assembly, and slide the hose clamp to secure it.


Hide 16261G 10.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the water by-pass pipe, and slide the hose clamp to secure it.


Hide 16572D 11.CONNECT NO. 2 RADIATOR HOSE

Hide 16057 12.CONNECT RADIATOR HOSE SUB-ASSEMBLY

a.

Connect the radiator hose sub-assembly to the cylinder head sub-assembly, and slide the hose clamp to secure it.


Hide 16581B 13.INSTALL RADIATOR HOSE HOSE CLAMP

a.

for Manual Transaxle:

i.

Install the radiator hose hose clamp.



b.

for Automatic Transaxle:

i.

Install the 2 radiator hose hose clamps.


ii.

Connect the No. 8 and No. 9 water by-pass hose to each radiator hose hose clamp.



Hide 53216A 14.INSTALL UPPER RADIATOR SUPPORT

a.

Install the upper radiator support with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16533B 15.INSTALL NO. 1 RADIATOR SUPPORT

a.

Install the 2 No. 1 radiator supports with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16.CONNECT WIRE HARNESS

a.

Connect the 2 cooling fan motor connectors.


b.

Attach the 9 wire harness clamps to connect the wire harness.


Hide 16681 19.INSTALL RADIATOR UPPER AIR GUIDE PLATE

a.

Install the radiator upper air guide plate with the 6 clips.


Hide 52029 20.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly with the 3 bolts.


b.

Connect the horn connector.


Hide 53630 21.CONNECT HOOD LOCK CONTROL CABLE ASSEMBLY

a.

Attach the clamp to connect the hood lock control cable assembly.


Hide 53629 23.INSTALL HOOD LOCK CONTROL CABLE COVER (w/ Cover)

Hide 74404A 24.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 27.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 16683 30.INSTALL RADIATOR LOWER AIR GUIDE PLATE

a.

Attach the 2 claws and install the radiator lower air guide plate.


Hide 52618 31.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Install the front lower bumper absorber with 4 screws.


Hide 51441 32.INSTALL NO. 1 ENGINE UNDER COVER